CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] CNC: Spindle speed control

Posted by James Cullins
on 2003-03-25 16:06:58 UTC
Mach1 is capable of controlling spindle speed by G code Via PWM signal to a
controller.
Jim
----- Original Message -----
From: "J. Malte Stoeckhert" <malte.stoeckhert@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, March 25, 2003 4:02 PM
Subject: [CAD_CAM_EDM_DRO] CNC: Spindle speed control


> Hi there,
>
> After doing some research about CAD/CAM/CNC I have one unresolved
> question remaining:
>
> All of the systems/information I have seen so far seems to disregard
> spindle speed control via g-code which seems funny to me as the
> spindle speed besides the feed rate is an important factor in
> cutting/turning (I'm still a early beginner in metal cutting).
>
> Is the
reafeasableandfinanciallyreasonablesolutionIownaSherlinemillandlatheMalteAdd
ressesFAQhttpwww.ktmarketing.comfaq.htmlFILEShttpgroups.yahoo.comgroupCAD_CA
M_EDM_DROfilesPostMessagesCAD_CAM_EDM_DRO@...6Subscribe
CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

J. Malte Stoeckhert 2003-03-25 14:02:35 UTC CNC: Spindle speed control Bob Simon 2003-03-25 14:22:57 UTC Low cost torque amplifier caudlet 2003-03-25 14:37:18 UTC Re: CNC: Spindle speed control Andrew Mawson 2003-03-25 14:44:12 UTC Re: CNC: Spindle speed control James Cullins 2003-03-25 16:06:58 UTC Re: [CAD_CAM_EDM_DRO] CNC: Spindle speed control Matt Shaver 2003-03-25 17:04:45 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Jon Elson 2003-03-25 22:04:50 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Peter Cruickshank 2003-03-26 02:37:46 UTC Re: CNC: Spindle speed control Peter Cruickshank 2003-03-26 03:00:40 UTC CNC: Spindle speed control - F to V Bob Simon 2003-03-26 06:41:33 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Erie Patsellis 2003-03-26 07:19:14 UTC RE: [CAD_CAM_EDM_DRO] Re: CNC: Spindle speed control J. Malte Stoeckhert 2003-03-26 08:34:11 UTC Re: CNC: Spindle speed control ccq@x... 2003-03-26 12:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC: Spindle speed control Peter Cruickshank 2003-03-27 04:27:44 UTC Re: CNC: Spindle speed control