CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: CNC: Spindle speed control

Posted by ccq@x...
on 2003-03-26 12:29:03 UTC
Hi guys;

If you have the proper files for making the circuit boards, you can have them
made by one of the many companies that provide just that service. Some of them
aren't all that expensive for one-offs. I can probably dig up a few URLs if you
need them, but you should be able get quicker results with a web search.

Bill

On Wed Mar 26 08:33:49 2003 J. Malte Stoeckhert wrote:

>Andrew and all,
>
>Thx for the help. Well I'm defintely not into electronics yet (I try
>to focus on teaching myself machining) so building a circuit board is
>out of my reach.
>
>I keep the information in my stack of future projects!
>
>Malte
>
>
>> Malte,
>>
>> What I have done is to hang a simple digital to analogue converter
>> onto a parallel port, and use its output to drive the 0-10v input
>of
>> a VFD.
>>
>> I'm running TurboCNC, and as the source code is available, I have
>> been able to incorporate simple drivers for M03 / M04 / M05 & SXXX
>> and it works very nicely.
>>
>> If you go to the TurboCNC user group on Yahoo, I have posted the
>> circuit diagram and the code in the files section
>> (schematic_page_2.pdf & vfd.pas)
>>
>> Regards,
>>
>> Andrew Mawson
>> Bromley,
>> Kent,
>> UK

--
----------------------------------------------------------------------------
RKBA! ***** Blessings On Thee, Oh Israel! ***** 4-19!
----------------+----------+--------------------------+---------------------
An _EFFECTIVE_ | Insured | All matter is vibration. | Let he who hath no
weapon in every | by COLT; | -- Max Planck | weapon sell his
hand = Freedom | DIAL | In the beginning was the | garment and buy a
on every side! | 1911-A1. | word. -- The Bible | sword.--Jesus Christ
----------------+----------+--------------------------+---------------------

Constitutional Government is dead; LONG LIVE THE CONSTITUTION!!!!!

----------------------------------------------------------------------------

Discussion Thread

J. Malte Stoeckhert 2003-03-25 14:02:35 UTC CNC: Spindle speed control Bob Simon 2003-03-25 14:22:57 UTC Low cost torque amplifier caudlet 2003-03-25 14:37:18 UTC Re: CNC: Spindle speed control Andrew Mawson 2003-03-25 14:44:12 UTC Re: CNC: Spindle speed control James Cullins 2003-03-25 16:06:58 UTC Re: [CAD_CAM_EDM_DRO] CNC: Spindle speed control Matt Shaver 2003-03-25 17:04:45 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Jon Elson 2003-03-25 22:04:50 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Peter Cruickshank 2003-03-26 02:37:46 UTC Re: CNC: Spindle speed control Peter Cruickshank 2003-03-26 03:00:40 UTC CNC: Spindle speed control - F to V Bob Simon 2003-03-26 06:41:33 UTC Re: [CAD_CAM_EDM_DRO] Low cost torque amplifier Erie Patsellis 2003-03-26 07:19:14 UTC RE: [CAD_CAM_EDM_DRO] Re: CNC: Spindle speed control J. Malte Stoeckhert 2003-03-26 08:34:11 UTC Re: CNC: Spindle speed control ccq@x... 2003-03-26 12:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC: Spindle speed control Peter Cruickshank 2003-03-27 04:27:44 UTC Re: CNC: Spindle speed control