Re: Pleaes help !!! Stepper Motor Question.
Posted by
shawnusa2002
on 2003-05-08 17:40:31 UTC
Thanks for the reply. I confirmed that the earth shield wire was
just mearly grounded to the motor case as you guessed. So I infact
have a 4 wire Stepper. What does this mean? I was all planned out to
use a 8 wire stepper with a Compumotor 8 wire drivers I picked up.
Now, I have no clue what to do from here.
1. Is this 4 wire stepper Uni or Bi Polar?
2. Can I use this with the 210 or 201 Geckos?
3. Which Gecko model if any should I choose (201 or 210)?
4. Am I better off getting diffrent motors?
I plan to upgrade a HF Mini Mill with these. And to think. I still
have to choose screws types for the z-axis and pick a nice software
package. Man what one goes through to get to the art of CNC.
Anyway, I'm kinda stumped now on what I should do next. Any help is
greatly appricated.
Thanks,
Shawn
just mearly grounded to the motor case as you guessed. So I infact
have a 4 wire Stepper. What does this mean? I was all planned out to
use a 8 wire stepper with a Compumotor 8 wire drivers I picked up.
Now, I have no clue what to do from here.
1. Is this 4 wire stepper Uni or Bi Polar?
2. Can I use this with the 210 or 201 Geckos?
3. Which Gecko model if any should I choose (201 or 210)?
4. Am I better off getting diffrent motors?
I plan to upgrade a HF Mini Mill with these. And to think. I still
have to choose screws types for the z-axis and pick a nice software
package. Man what one goes through to get to the art of CNC.
Anyway, I'm kinda stumped now on what I should do next. Any help is
greatly appricated.
Thanks,
Shawn
> Check the wires to the case with a meter. My guess is that theearth is
> just a ground wire to the case and does not connect to the phasewires.
> I have had some motors like that and just ignores the shield.into a
>
> Tim
> [Denver, CO]
> Sherline products at Deep Discount
> Mach1 & DeskCNC with credit card ordering
> www.KTMarketing.com/Sherline
> Now selling Visual Mill 4.0
>
>
> > -----Original Message-----
> > I have 3 Compumotor M83-135's. I just recieved them in the mail
> > today and what I thought was a eight wire stepper has turned
> > 5 wire setup. I do not know if this is a Unipolar or Bi-Polar
> > stepper. The wire setup is as follows
> >
> > Phase 1 + Wht
> > Phase 1 - GRN
> > Phase 2 + BLK
> > Phase 2 - RED
> > Bar wire - Earth shield
Discussion Thread
shawnusa2002
2003-05-08 17:06:39 UTC
Pleaes help !!! Stepper Motor Question.
Tim Goldstein
2003-05-08 17:11:03 UTC
RE: [CAD_CAM_EDM_DRO] Pleaes help !!! Stepper Motor Question.
shawnusa2002
2003-05-08 17:40:31 UTC
Re: Pleaes help !!! Stepper Motor Question.
caudlet
2003-05-08 19:46:16 UTC
Re: Pleaes help !!! Stepper Motor Question.
Ross
2003-05-08 20:08:50 UTC
Re: Pleaes help !!! Stepper Motor Question.
Jon Elson
2003-05-08 21:26:58 UTC
Re: [CAD_CAM_EDM_DRO] Pleaes help !!! Stepper Motor Question.
Chris Baugher
2003-05-08 21:36:14 UTC
Re: [CAD_CAM_EDM_DRO] Pleaes help !!! Stepper Motor Question.
shawnusa2002
2003-05-08 22:08:16 UTC
Re: Pleaes help !!! Stepper Motor Question.
shawnusa2002
2003-05-08 22:09:48 UTC
Re: Pleaes help !!! Stepper Motor Question.
Chris Baugher
2003-05-09 11:29:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pleaes help !!! Stepper Motor Question.