CAD CAM EDM DRO - Yahoo Group Archive

Re: Bleeder resistor for power supply size?

on 2003-07-07 06:01:02 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Mariss Freimanis"
<mariss92705@y...> wrote:
> Hi,
>
> This is one of those "how many angels can dace on the end of a pin"
> questions that come up again and again.
>
> A capacitor stores a charge (voltage) for a long time if there is
no
> load on it.
>
> That is not the way you are going to use your supply.
>
> You will have various drives and other loads on it and you will
turn
> the supply on and off on the AC input to your supply.
>
> With all these various drives and loads, your supply will very
> quickly discharge (<< 1 sec) when you shut off the AC supply.
>
> You never switch the loads on and off on the DC side. That is hard
on
> the switch and any electronics attached to it. You use the AC power
> input for that.
>
> You do that and there is no reason for a "bleeder resistor". It is
a
> pointless, sometimes expensive component that does precisely
nothing
> except get hot.
>
> Long and short, turn your power on-off at the AC side and let your
> drives be the "bleeders". They will do a better job than any
resistor
> and they will do it quicker and better for free.
>
> Mariss



I think of all the solutions, I liked the fans in series one. just
get a few cooling fans in series to be higher than the DC bus and if
you hear them running, you got power.

Dave

Discussion Thread

John Guenther 2003-07-06 04:27:38 UTC Bleeder resistor for power supply size? Jon Elson 2003-07-06 12:41:35 UTC Re: [CAD_CAM_EDM_DRO] Bleeder resistor for power supply size? John Guenther 2003-07-06 15:01:25 UTC RE: [CAD_CAM_EDM_DRO] Bleeder resistor for power supply size? Tim Goldstein 2003-07-06 15:10:03 UTC RE: [CAD_CAM_EDM_DRO] Bleeder resistor for power supply size? stevenson_engineers 2003-07-06 15:56:52 UTC Re: Bleeder resistor for power supply size? Tim Goldstein 2003-07-06 16:06:40 UTC RE: [CAD_CAM_EDM_DRO] Re: Bleeder resistor for power supply size? wanliker@a... 2003-07-06 17:25:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Bleeder resistor for power supply size? turbulatordude 2003-07-06 18:29:00 UTC Re: Bleeder resistor for power supply size? JanRwl@A... 2003-07-06 19:25:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Bleeder resistor for power supply size? Damon 2003-07-06 20:18:40 UTC Re: Bleeder resistor for power supply size? turbulatordude 2003-07-06 20:41:51 UTC Re: Bleeder resistor for power supply size? Mariss Freimanis 2003-07-06 20:44:43 UTC Re: Bleeder resistor for power supply size? turbulatordude 2003-07-07 06:01:02 UTC Re: Bleeder resistor for power supply size? ben_englund 2003-07-07 08:13:01 UTC Re: Bleeder resistor for power supply size? jchrisj7734 2003-07-08 23:18:12 UTC Re: Bleeder resistor for power supply size?