[CAD_CAM_EDM_DRO] I looked into another EDM Software design program
Posted by
glee@i...
on 2003-07-30 18:39:25 UTC
Although I have no plans to get into EDM, the subject fascinates me and I
have been following the EDM discussion with interest.
I know that the Dolphin Partmaster CAD/CAM Software that I purchased
includes EDM support, but I did not know what it could or could not do, or
even what to ask.
I wrote the folks at Dolphin, and here is there reply.
We currently support 2 and 4 Axes Wire EDM programming.
The 4 Axes can be programmed either by defining two separate Contours or by
defining one Contour and applying angle movement to the Wire.
We are expecting to release a new EDM module in August, the product is in
the final stages of testing and should be ready in a few eeeks.
I hope this information is helpful.
-Eric
have been following the EDM discussion with interest.
I know that the Dolphin Partmaster CAD/CAM Software that I purchased
includes EDM support, but I did not know what it could or could not do, or
even what to ask.
I wrote the folks at Dolphin, and here is there reply.
We currently support 2 and 4 Axes Wire EDM programming.
The 4 Axes can be programmed either by defining two separate Contours or by
defining one Contour and applying angle movement to the Wire.
We are expecting to release a new EDM module in August, the product is in
the final stages of testing and should be ready in a few eeeks.
I hope this information is helpful.
-Eric
Discussion Thread
deansala
2003-07-30 11:29:03 UTC
How to you make a 1/8" collet on a 1/4" shaft
doug98105
2003-07-30 12:57:48 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
turbulatordude
2003-07-30 13:23:37 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
mayfieldtm
2003-07-30 13:52:49 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
deansala
2003-07-30 13:55:20 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
Carl Mikkelsen
2003-07-30 14:34:53 UTC
Re: [CAD_CAM_EDM_DRO] How to you make a 1/8" collet on a 1/4" shaft
turbulatordude
2003-07-30 15:28:27 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
turbulatordude
2003-07-30 15:29:58 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
Harvey White
2003-07-30 16:12:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: How to you make a 1/8" collet on a 1/4" shaft
dodge1320
2003-07-30 17:15:08 UTC
Re: How to you make a 1/8" collet on a 1/4" shaft
glee@i...
2003-07-30 18:39:25 UTC
[CAD_CAM_EDM_DRO] I looked into another EDM Software design program
turbulatordude
2003-07-30 20:51:07 UTC
Re: I looked into another EDM Software design program
Denis Casserly
2003-07-31 12:24:47 UTC
Re: [CAD_CAM_EDM_DRO] How to you make a 1/8" collet on a 1/4" shaft