Re: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?
Posted by
Jon Elson
on 2003-08-27 10:47:20 UTC
foxprints2003 wrote:
operations
to cause a hitch in the motion. There is a feature that allows the number
of times a second the GUI is allowed to run
in the [DISPLAY] section of the .ini file
; Cycle time, in seconds, that display will sleep between polls
CYCLE_TIME = 0.200
I usually decrease this to .100 seconds just to get more responsive GUI
operation. You might try decreasing this quite a bit to see if it helps.
Jon
>--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:That's what I was trying to say, is that it was intended for these
>
>
>> I think the problem may
>>
>>
>be
>
>
>>related to
>>the fact that the auxilliary I/O is handled in the Linux part of
>>
>>
>EMC, while
>
>
>>motion is done by the real-time part. I suspect that the pause is
>>
>>
>when
>
>
>>these
>>two parts are synchronizing for these operations.
>>
>>Jon
>>
>>
>
>This must be done by the interpreter because the pause is not due to
>lack of processing speed, the system decelerates to a stop turns on
>the output immediately after stopping & then accelerates back into
>the next move. Clearly the system planned the stop due to the m code
>insertion. I can't imagine turning on a single discrete output would
>require nearly as much processing time as anything else.
>
>
operations
to cause a hitch in the motion. There is a feature that allows the number
of times a second the GUI is allowed to run
in the [DISPLAY] section of the .ini file
; Cycle time, in seconds, that display will sleep between polls
CYCLE_TIME = 0.200
I usually decrease this to .100 seconds just to get more responsive GUI
operation. You might try decreasing this quite a bit to see if it helps.
Jon
Discussion Thread
foxprints2003
2003-08-26 12:50:38 UTC
EMC - M codes pause motion?
turbulatordude
2003-08-26 14:58:40 UTC
Re: EMC - M codes pause motion?
foxprints2003
2003-08-26 15:05:07 UTC
Re: EMC - M codes pause motion?
Paul
2003-08-26 15:30:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?
Matt Shaver
2003-08-26 15:37:33 UTC
Re: [CAD_CAM_EDM_DRO] EMC - M codes pause motion?
foxprints2003
2003-08-26 16:26:41 UTC
Re: EMC - M codes pause motion?
foxprints2003
2003-08-26 16:29:39 UTC
Re: EMC - M codes pause motion?
doug98105
2003-08-26 17:59:27 UTC
Re: EMC - M codes pause motion?
Fred Smith
2003-08-26 18:29:46 UTC
Re: EMC - M codes pause motion?
doug98105
2003-08-26 19:52:25 UTC
Re: EMC - M codes pause motion?
Damon
2003-08-26 20:13:09 UTC
Re: EMC - M codes pause motion?
Jon Elson
2003-08-26 22:50:27 UTC
Re: [CAD_CAM_EDM_DRO] EMC - M codes pause motion?
foxprints2003
2003-08-27 04:41:09 UTC
Re: EMC - M codes pause motion?
Jon Elson
2003-08-27 10:47:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?
Alan Marconett KM6VV
2003-08-27 12:38:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?
foxprints2003
2003-08-27 13:34:45 UTC
Re: EMC - M codes pause motion?
Leslie M. Watts
2003-08-27 15:06:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?
Jon Elson
2003-08-27 22:23:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC - M codes pause motion?