RE: [CAD_CAM_EDM_DRO] Minertia Motors

Harvey,
I have done some bench testing and found out the proper hookup to at least a
geckodrive 320. The encoder is black enc-, red enc+, white is phaseA, green
is phaseB. The encoder is 750 for 1 revolution of the motor. So 750 times
the lead screw pitch gives your pulses per inch. The motor leads go to the
arm+ and - if you have these reversed it will fault out immediately.
I have been running these at 80ipm no problem on the bench.
Derek

> -----Original Message-----
> From: Derek B. [
>
>
> I am also looking for info on motor #2 as I have quite a few of these. I
> think the first number might not be right though. Mine says
> T01L-ST33 and I also have ST34 's
> The PN# is right on.
> The encoder has 4 wires red,black,green, and white. The red and black look
> like power. White and green are A and B encoder.
> Derek B.
> http://groups.yahoo.com/group/Denver_CNC_Club/
>
>
>
> > -----Original Message-----
> > From: Harvey White
> >
> >
> > I've looked at the Yasakawa company web site, done a search on Google,
> > and have not come up with any data on two motors I have.
> >
> > Any help would be appreciated. Both of these have encoders.
> >
> > motor 1:
> >
> > UGRMEM-02SAK0E
> > UTOPI-080MX
> > "RM Series"
> >
> > Has an encoder... 400:1, 2 phase, iirc... (used a counter..)
> > motor is roughly 4 inches by 1 1/2
> >
> > Motor 2:
> > "Mini-Series"
> > 101L-ST33
> > 410611703-C EC29145
> >
> > Has an encoder. ratio yet unknown....
> > motor is roughly 1 inch by 3 inches.
> > will run on roughly 1.4 volts to 24 or so.
> >
> > Harvey
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > wanliker@..., timg@...
> > Moderator: pentam@... indigo_red@... [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
> > to be a sister site to the CCED group, as many of the same
> > members are there, for OT subjects, that are not allowed on the
> CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> >
> >
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this
> to be a sister site to the CCED group, as many of the same
> members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>