Re: [CAD_CAM_EDM_DRO] Minertia Motors

On Thu, 28 Aug 2003 00:10:37 -0600, you wrote:

>I am also looking for info on motor #2 as I have quite a few of these. I
>think the first number might not be right though. Mine says
>T01L-ST33 and I also have ST34 's

You're right on the first number. I looked again and it is a
T01L-ST33.

>The PN# is right on.
>The encoder has 4 wires red,black,green, and white. The red and black look
>like power. White and green are A and B encoder.

I had a the bell end off the encoder of the larger motors, and the
voltage was 5.0 volts. It was, I think, marked on the circuit board.

Harvey

>Derek B.
>http://groups.yahoo.com/group/Denver_CNC_Club/
>
>
>
>> -----Original Message-----
>> From: Harvey White
>>
>>
>> I've looked at the Yasakawa company web site, done a search on Google,
>> and have not come up with any data on two motors I have.
>>
>> Any help would be appreciated. Both of these have encoders.
>>
>> motor 1:
>>
>> UGRMEM-02SAK0E
>> UTOPI-080MX
>> "RM Series"
>>
>> Has an encoder... 400:1, 2 phase, iirc... (used a counter..)
>> motor is roughly 4 inches by 1 1/2
>>
>> Motor 2:
>> "Mini-Series"
>> 101L-ST33
>> 410611703-C EC29145
>>
>> Has an encoder. ratio yet unknown....
>> motor is roughly 1 inch by 3 inches.
>> will run on roughly 1.4 volts to 24 or so.
>>
>> Harvey
>>
>>
>>
>>
>>
>> Addresses:
>> FAQ: http://www.ktmarketing.com/faq.html
>> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
>> wanliker@..., timg@...
>> Moderator: pentam@... indigo_red@... [Moderators]
>> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>> OFF Topic POSTS: General Machining
>> If you wish to post on unlimited OT subjects goto:
>> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
>> reach it if you have trouble.
>> http://www.metalworking.com/news_servers.html
>>
>> http://groups.yahoo.com/group/jobshophomeshop I consider this
>> to be a sister site to the CCED group, as many of the same
>> members are there, for OT subjects, that are not allowed on the CCED list.
>>
>> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
>> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
>> EXCEPTIONS........
>> bill
>> List Mom
>> List Owner
>>
>>
>>
>> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>>
>>
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>