CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] toroid transformer

Posted by Thomas Powell
on 2003-10-02 09:14:47 UTC
Thanks for all the help. Just getting some info together.
==============================================
Thomas Powell (VMOA 741)
1994 NOS injected T-Boost sales
Tourmaster V-Max Clear clutch cover sales
"LAFGAS" Handlebar brackets
Contact me at: tppjr@...
http://imageevent.com/tppjr (photopage)
==============================================

----- Original Message -----
From: "Jon Elson" <elson@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, September 30, 2003 3:59 PM
Subject: Re: [CAD_CAM_EDM_DRO] toroid transformer


>
>
> Thomas Powell wrote:
>
> >What DC voltage and amperage would I be able to get from a toroid
> >transformer with these specs? Running with 220 input.
> >
> >115/230 Volt, 50/60Hz Output: 20 VAC @ 10 AAC 118 VAC @ 13 AAC
> >
> >
> >
> Well, this is probably a bad choice, as most of the transformer is
> devoted to the 118 VAC winding. The 118 V winding produces
> 118*13 = 1534 W, the 20 VAC winding produces 200 W. The
> 118 V winding is 94% of the transformer's output, the 20 V
> winding is only 6%. But, using a full wave bridge on the 20 V
> winding, you would get 28 VDC, with the 118 V winding you'd
> get 167 V DC. Using the 20 V winding counter to the 118
> V winding you'd get 98 VAC, rectified you'd have 139V DC.
> I don't know if any of these voltages are close to what you
> are looking for.
>
> Jon
>

Discussion Thread

Thomas Powell 2003-09-30 16:07:24 UTC toroid transformer Jon Elson 2003-09-30 19:00:27 UTC Re: [CAD_CAM_EDM_DRO] toroid transformer turbulatordude 2003-09-30 19:57:58 UTC Re: toroid transformer Bill Kichman 2003-09-30 21:51:04 UTC Re: [CAD_CAM_EDM_DRO] toroid transformer mmurray701 2003-10-01 07:59:08 UTC Re: toroid transformer turbulatordude 2003-10-01 16:03:28 UTC Re: toroid transformer - out of phase mmurray701 2003-10-01 16:48:59 UTC Re: toroid transformer - out of phase turbulatordude 2003-10-01 17:38:03 UTC Re: toroid transformer - out of phase Antonius J.M. Groothuizen 2003-10-01 19:34:55 UTC Re: toroid transformer - back to basics Jon Elson 2003-10-01 23:02:47 UTC Re: [CAD_CAM_EDM_DRO] Re: toroid transformer - out of phase Thomas Powell 2003-10-02 09:14:47 UTC Re: [CAD_CAM_EDM_DRO] toroid transformer Thomas Powell 2003-10-03 23:30:18 UTC Re: [CAD_CAM_EDM_DRO] Re: toroid transformer - back to basics turbulatordude 2003-10-04 05:06:37 UTC Re: toroid transformer - back to basics Thomas Powell 2003-10-05 00:04:29 UTC Re: [CAD_CAM_EDM_DRO] Re: toroid transformer - back to basics