Re: [CAD_CAM_EDM_DRO] General servo and controller questions
Posted by
james_cullins@s...
on 2004-02-23 05:29:14 UTC
If you use the parallel port you can use the Gecko or Rutex both are good
drives.
Both are step and direction input drives.
Jim
drives.
Both are step and direction input drives.
Jim
----- Original Message -----
From: "cressmx83" <cressmx83@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Sunday, February 22, 2004 5:11 PM
Subject: [CAD_CAM_EDM_DRO] General servo and controller questions
>
> Hello,
>
> I've set up a small stepper system, and it's been running well.
> Recently I've been looking at servo systems, specifically DC
> brushless servos, but I'm overwhelmed with all the terminology. With
> no comprehensive source of information, I've just been reading and
> gleaning information to little avail. It's been frustrating, so I'm
> posting some of my questions here, hopefully someone can point me in
> the right direction.
>
>
> My understanding of these brushless servo systems is that they
> controlled with a PC motion controller card -> servo amplifier ->
> servo.
>
> OR
>
> If I want to use the parallel port interface with the computer, I can
> get the rutex R991H to generate the signals to the amplifier.
> Parallel port -> Rutex board -> Servo amplifer -> Servo.
>
> I found the Rutex R991H here:
> http://www.rutex.com/us/cart.php?
> target=product&action=view&product_id=15&category_id=5
>
>
> I've purchased some of these AMC amplfiers:
> http://www.a-m-c.com/download/b30a.pdf
>
> Is it possible to wire the Rutex with the AMC amplifiers? I believe
> the AMC ones are "analog command input." I've looked at the manual
> and I'm completely lost as to how to wire these things. For example,
> where would the +/- 10 V signal from the Rutex go?
>
>
> In general, my questions are:
>
> 1. How are the servos wired to their controllers? For example, how
> would I wire the AMC amplifiers to the Rutex R991H? Or how would I
> wire the AMC amplifiers to a motion controller card?
>
> 2. What are the meaning of terms like current, open loop voltage,
> tachometer, and Hall velocity? And are there different types of
> brushless DC servos?
>
> Sorry if my questions are too elementary. I'd really appreciate it if
> someone could point me to a source of information that would answer
> these types of questions (books, websites...). I'd like to obtain a
> holistic understanding rather than ask questions on a case by case
> basis.
>
> Thanks,
> Jim
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
Discussion Thread
cressmx83
2004-02-22 22:00:44 UTC
General servo and controller questions
james_cullins@s...
2004-02-23 05:29:14 UTC
Re: [CAD_CAM_EDM_DRO] General servo and controller questions
caudlet
2004-02-23 07:59:31 UTC
Re: General servo and controller questions
Jon Elson
2004-02-23 09:30:18 UTC
Re: [CAD_CAM_EDM_DRO] General servo and controller questions
james_cullins@s...
2004-02-23 10:11:53 UTC
Re: [CAD_CAM_EDM_DRO] General servo and controller questions
Lindsay
2004-02-23 17:04:49 UTC
Re: [CAD_CAM_EDM_DRO] General servo and controller questions
Jon Elson
2004-02-23 19:59:07 UTC
Re: [CAD_CAM_EDM_DRO] General servo and controller questions