Re: [CAD_CAM_EDM_DRO] controlling hydraulics with Mach 2

Hi Bob,
Thanks for the reply. I will check into the Galil chips, sounds like an idea
worth checking into.
Did Galil send a schematic to aid in hook up?

Shawn

----- Original Message -----
From: "Bob Muse" <mtebob1@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Sunday, June 06, 2004 8:13 PM
Subject: Re: [CAD_CAM_EDM_DRO] controlling hydraulics with Mach 2


> Hi Shawn
> I used the standard release of cncpro, which I'm still using. I like it
> even though it's got a couple of "peculiarities". The board I built would
> work with any step and direction type software. The Galil chips used were
> GL-1200. They take step and direction input, along with the encoder
> feedback and output +/- 10 volts to an analog servo amp. They have a PID
> filter etc. I am very happy with the setup. The chips cost around $100
> each (need one per axis) plus a few other bits and pieces and the labor to
> build the board. May not be the most cost effective way to do this today.
>
> Bob
>
>
> ----- Original Message -----
> From: "Shawncd" <shawncd@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Saturday, June 05, 2004 7:25 PM
> Subject: Re: [CAD_CAM_EDM_DRO] controlling hydraulics with Mach 2
>
>
> > Hi Bob,
> > Did Yeager automation customize there software to work with Galil motion
> > control cards?
> >
> > Shawn
> >
> >
> > ----- Original Message -----
> > From: "Bob Muse" <mtebob1@...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Saturday, June 05, 2004 1:22 PM
> > Subject: Re: [CAD_CAM_EDM_DRO] controlling hydraulics with Mach 2
> >
> >
> > > Hi Todd
> > >
> > > I had the same idea about 8 years ago. I had a cintimatic mill with
> > > hydraulic servos and a bad control. I retrofitted a PC using CNCPro
and
> a
> > > motion board with Galil chips. Spent a couple days building the
> > electronic
> > > interface and installing encoders and then watching the table try to
> leap
> > > off the ways!! I scrapped that idea and installed dc servo amps and
> > motors
> > > and it's been making chips ever since.
> > >
> > > There's a good reason why you seldom see a hydraulic servo on a
machine
> > tool
> > > any more. They were plagued with many problems. Of course, this is
> just
> > > my 2 cents worth.
> > >
> > > Regards,
> > > Bob
> > >
> > >
> > > ----- Original Message -----
> > > From: "Todd W. Syssa" <procisionengineering@...>
> > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > Sent: Saturday, June 05, 2004 12:01 PM
> > > Subject: [CAD_CAM_EDM_DRO] controlling hydraulics with Mach 2
> > >
> > >
> > > > Anyone out there ever control hydraulics with Mach 2
> > > > or other CNC PC based controller?
> > > >
> > > > I have a proportional hydraulic valve that uses 12 VDC
> > > > and varies fluid with current (.6-1.2 amps) as well as
> > > > an on off valve that uses 12 VDC to power the solenoid
> > > > for each direction.
> > > >
> > > > I also have a linear encoder attached to the carraige
> > > > of each slide and have gotten both encoders to work
> > > > with the Mach 2 demo. My question is about converting
> > > > the output used for a servo/stepper motor to making it
> > > > useful for turning on and off the hydrualic
> > > > cylinders...
> > > >
> > > > ...is modifying a servo amplifier a possibilty? Any
> > > > ideas would be helpful!
> > > >
> > > > Thanks,
> > > > Todd W
> > > >
> > > >
> > > >
> > > >
> > > > __________________________________
> > > > Do you Yahoo!?
> > > > Friends. Fun. Try the all-new Yahoo! Messenger.
> > > > http://messenger.yahoo.com/
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > >
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@...,
> > > timg@...
> > > > Moderator: pentam@... indigo_red@...
davemucha@...
> > > [Moderators]
> > > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
it
> > if
> > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider this to
be
> a
> > > sister site to the CCED group, as many of the same members are there,
> for
> > OT
> > > subjects, that are not allowed on the CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > > bill
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> > timg@...
> > > Moderator: pentam@... indigo_red@... davemucha@...
> > [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this to be
a
> > sister site to the CCED group, as many of the same members are there,
for
> OT
> > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> > Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if
> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
OT
> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>