Re: [CAD_CAM_EDM_DRO] Re: Gecko burned - fixed for now
Posted by
Les Newell
on 2004-11-12 03:54:16 UTC
Hi Keith,
I will be using treadmill motors from surpluscenter.com, item number
10-1573. Carriage to the UK cost more than the motors but they are still
lots cheaper than anything I can get in this country. Surplus center
were very helpful.
The motors are designed to be foot mounted but they have a nice big
flange on them that can be drilled with the same bolt holes as the
current motors. They are smooth to turn by hand with only a little
'cogging' and will run down to about 1.5V.
I intend to use 200CPR encoders(giving 800 steps/rev) and I will
probably gear them down 4:1, giving a resolution of 16000 steps/inch.
The Z axis will probably stay 1:1 because I don't fancy trying to change
the belt :-)
I will go with Rutex drives, not because I have anything against the
Gecko drives but because I have future plans that will make use of the
SPI facility.
I will let you know how I get on...
Les
Keith Clark wrote:
I will be using treadmill motors from surpluscenter.com, item number
10-1573. Carriage to the UK cost more than the motors but they are still
lots cheaper than anything I can get in this country. Surplus center
were very helpful.
The motors are designed to be foot mounted but they have a nice big
flange on them that can be drilled with the same bolt holes as the
current motors. They are smooth to turn by hand with only a little
'cogging' and will run down to about 1.5V.
I intend to use 200CPR encoders(giving 800 steps/rev) and I will
probably gear them down 4:1, giving a resolution of 16000 steps/inch.
The Z axis will probably stay 1:1 because I don't fancy trying to change
the belt :-)
I will go with Rutex drives, not because I have anything against the
Gecko drives but because I have future plans that will make use of the
SPI facility.
I will let you know how I get on...
Les
Keith Clark wrote:
>
> Les, I am afraid I may be in the same boat. I hope at least that
> the GEcko might be repairable with the fuse there.
>
> Have you made a choice as to servo motors yet? As I remember, you
> have a Bridgeport too?
>
> Thanks,
>
> Keith
>
>
Discussion Thread
Keith Clark
2004-11-11 21:53:55 UTC
Gecko burned - fixed for now
Les Newell
2004-11-12 01:16:08 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - fixed for now
Keith Clark
2004-11-12 03:31:21 UTC
Re: Gecko burned - fixed for now
Les Newell
2004-11-12 03:54:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned - fixed for now
Keith Clark
2004-11-12 05:12:44 UTC
Re: Gecko burned - fixed for now
Les Newell
2004-11-12 05:33:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned - fixed for now
R Rogers
2004-11-12 08:42:08 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - fixed for now
Roy J. Tellason
2004-11-12 10:13:49 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - fixed for now
Andy Wander
2004-11-12 10:36:25 UTC
RE: [CAD_CAM_EDM_DRO] Gecko burned - fixed for now
Les Newell
2004-11-12 10:54:32 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - now motor types
R Rogers
2004-11-12 12:00:33 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - now motor types
Les Newell
2004-11-12 12:37:49 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - now motor types
Jon Elson
2004-11-12 20:48:40 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - now motor types
R Rogers
2004-11-13 09:49:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned - now motor types