CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper?

Posted by Darrell
on 2000-05-31 15:04:27 UTC
Do not confuse a 5 wire stepper with a 5 phase stepper. A 5 wire stepper is
a 4 coil stepper with one wire from each coil connected as common internally
and can only be run in unipolar mode. A 5 phase stepper has 5 coils and 10
wires, 2 for each coil. Fujitsu Limited made these and they were used on
some ICON controllers on some of the Wells Indexer machines. I suppose some
one may have made a 5 phase stepper with 6 wires, one for each coil and one
internally connected common but I have never seen one.
Darrell

----- Original Message -----
From: Jon Elson <jmelson@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Wednesday, May 31, 2000 2:26 PM
Subject: Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper?


>
>
> Darrell wrote:
>
> > A 5 phase stepper has 5 windings (10 wires) instead of 4 windings.
>
> Actually, the Vexta (Oriental Motor) 5 phase steppers (and nobody else
> makes
> them, I assume due to patent rights) have only 5 wires.
>
> > That
> > means it needs a special driver card.
>
> Very definitely so. The only ones I've ever seen are also from Vexta.
>
> Jon
>
>
> ------------------------------------------------------------------------
> Tired of searching?
> Get the right answer, fast, from someone who's been there - guaranteed.
> http://click.egroups.com/1/4520/3/_/423600/_/959808294/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Darrell 2000-05-31 12:30:24 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Jon Elson 2000-05-31 14:24:58 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? joe 2000-05-31 14:49:51 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Darrell 2000-05-31 15:04:27 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Darrell 2000-05-31 15:26:52 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Robert 2000-05-31 15:39:39 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Steve Carlisle 2000-05-31 16:25:27 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Steve Carlisle 2000-05-31 16:25:37 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Your Name 2000-05-31 19:55:49 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Jon Elson 2000-05-31 21:33:56 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper? Steve Carlisle 2000-06-01 07:01:07 UTC Re: [CAD_CAM_EDM_DRO] What is a 5 Phase stepper?