Re: [CAD_CAM_EDM_DRO] CAM software
Posted by
cnc002@a...
on 2005-04-27 13:37:35 UTC
In a message dated 4/27/2005 2:59:38 PM Eastern Daylight Time,
tiwanacote@... writes:
Hi!
Please!! Some one could tell me about any program with:
Uses the parallel port sending step and direction signals (For use with
drivers like Grecko ones).
For milling 3D models
Read DXF files
Frendly
Do not exceed 300 u$s
Regards
Maximiliano
Also take a look at cncPro at _www.yeagerautomation.com_
(http://www.yeagerautomation.com) it is less than $300.00 USD and will do up to 4 axis. The
only real drawback that I found was that it doesn't have tool comp and it runs
in DOS. Otherwise it is very good piece of software.
Randy
[Non-text portions of this message have been removed]
tiwanacote@... writes:
Hi!
Please!! Some one could tell me about any program with:
Uses the parallel port sending step and direction signals (For use with
drivers like Grecko ones).
For milling 3D models
Read DXF files
Frendly
Do not exceed 300 u$s
Regards
Maximiliano
Also take a look at cncPro at _www.yeagerautomation.com_
(http://www.yeagerautomation.com) it is less than $300.00 USD and will do up to 4 axis. The
only real drawback that I found was that it doesn't have tool comp and it runs
in DOS. Otherwise it is very good piece of software.
Randy
[Non-text portions of this message have been removed]
Discussion Thread
Brent Fuchs
2002-10-26 17:18:24 UTC
CAM software
carlcnc
2002-10-26 18:33:33 UTC
Re: CAM software
carlcnc
2002-10-26 18:36:04 UTC
Re: CAM software
Jeffrey Gough
2003-07-27 09:46:46 UTC
CAM software
Harvey White
2003-07-27 10:11:49 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Tim Goldstein
2003-07-27 10:12:31 UTC
RE: [CAD_CAM_EDM_DRO] CAM software
Paul
2003-07-27 10:18:31 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Fred Smith
2003-07-27 10:49:05 UTC
Re: CAM software
Jon Elson
2003-07-27 11:19:36 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Charles Knight
2003-07-27 12:12:45 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Charles Hixon
2003-07-27 15:03:50 UTC
Re: CAM software
jeffreydouglasgough
2003-07-27 18:34:26 UTC
Re: CAM software
Nick Ibbitson
2004-05-09 13:30:21 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Gregory Kamysz
2004-05-09 15:40:18 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Nick Ibbitson
2004-05-10 01:38:20 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
Maxi Bertotto
2005-04-27 11:58:03 UTC
CAM software
Robert Campbell
2005-04-27 12:10:59 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
caudlet
2005-04-27 12:14:13 UTC
Re: CAM software
Doug Fortune
2005-04-27 12:47:25 UTC
manual for a Mitsubishi "Frequol F2" VFD anyone?
cnc002@a...
2005-04-27 13:37:35 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
cnc002@a...
2005-04-27 13:39:03 UTC
Re: [CAD_CAM_EDM_DRO] manual for a Mitsubishi "Frequol F2" VFD anyone?
Doug Fortune
2005-04-27 16:08:16 UTC
Re: [CAD_CAM_EDM_DRO] manual for a Mitsubishi "Frequol F2" VFD anyone?
JCullins
2005-04-27 18:47:45 UTC
Re: [CAD_CAM_EDM_DRO] CAM software
YOU
2008-10-19 13:20:48 UTC
CAM software
rbtoolcnc
2008-10-20 11:35:56 UTC
Re: CAM software
roboticscnc
2008-10-21 08:28:52 UTC
Re: CAM software