RE: [CAD_CAM_EDM_DRO] Re: HP QEDS encoder

Oh dear, that'd pretty much be the end of it....

> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com]On Behalf Of John Meissner
> Sent: Thursday, 19 May 2005 12:01 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: HP QEDS encoder
>
>
> That is.....unless the installer used "locktite" or some sealant on
> the hub...as I have found out. :)
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Paul Kelly" <tech@c...>
> wrote:
> > Got it sorted.. :-)
> > You will need:
> > a). a 1/32" hex wrench
> > b). a small torch
> > c). a LOT of patience
> >
> > Take a screwdriver and rotate the large round section on the back
> of the
> > encoder counter clockwise (and inwards) from the "Two dot"
> setting, to the
> > "One dot" setting.
> > This opens up a small slot on the side of the encoder, in line
> with the
> > screwdriver slot you just used.
> > Take a torch and peer into this slot whilst rotating the shaft.
> You'll just
> > be able to see the hub set screw as it passes (my encoder had a
> small length
> > of tube behind the slot that made this a bit harder).
> >
> > All you have to do now is insert the little hex wrench and back
> off that set
> > screw. A simple task that should take no more and half an hour to
> get
> > right!!!!
> >
> >
> > You can then either undo the external mounting bolts or unclip the
> back
> > cover of the encoder. It should then just slide off.
> >
> > Good luck and thanks to those that replied with advice and support.
> >
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this
> to be a sister site to the CCED group, as many of the same
> members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>