RE: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Posted by
Alan Marconett
on 2005-05-19 08:19:28 UTC
HI Jon, Lance,
From information from an EMCO 5" CNC lathe setup, I believe this is a
"holding" current. It serves as the detent.
Alan KM6VV
From information from an EMCO 5" CNC lathe setup, I believe this is a
"holding" current. It serves as the detent.
Alan KM6VV
> -----Original Message-----
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
>
> Lance Hopper wrote:
>
> > I'm in the process of completely retrofitting an Emco Turn 120 cnc
> >lathe. It's got an 8 position tool turret on a ratchet mechanism,
> >driven by a small DC gearmotor (24VDC ~15watts) through a worm gear.
> > Would it be feasible to simply control the motor with a DPDT relay
> >that supplies 24VDC for forward operation, and then supply 5VDC and a
> >resistor of some value for reverse/stall operation?
> >
> > I'm not an electronics guru, so designing and building a circuit
> >would be very time consuming and difficult for me. I'll be
> >controlling everything with Mach 2. Thanks for any advice.
> >
> >
> Yes, this should work fine. But, I think you need one more relay to turn
> it off. It doesn't really keep the motor stalled ALL the time, does it?
> Or, just long enough to get the tool firmly seated?
>
> Jon
>
Discussion Thread
Lance Hopper
2005-05-18 09:52:47 UTC
how to safely stall a DC motor
Alex Holden
2005-05-18 10:17:52 UTC
Re: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Alan Marconett
2005-05-18 12:41:11 UTC
RE: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Lance Hopper
2005-05-18 15:10:22 UTC
Re: how to safely stall a DC motor
Jon Elson
2005-05-18 21:37:51 UTC
Re: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Les Newell
2005-05-19 01:14:32 UTC
Re: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Lance Hopper
2005-05-19 05:27:15 UTC
Re: how to safely stall a DC motor
Alex Holden
2005-05-19 05:54:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: how to safely stall a DC motor
Alex Holden
2005-05-19 06:02:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: how to safely stall a DC motor
doug98105
2005-05-19 06:03:17 UTC
Re: how to safely stall a DC motor
Les Newell
2005-05-19 06:58:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: how to safely stall a DC motor
Jon Elson
2005-05-19 08:05:57 UTC
Re: [CAD_CAM_EDM_DRO] how to safely stall a DC motor
Alan Marconett
2005-05-19 08:19:28 UTC
RE: [CAD_CAM_EDM_DRO] how to safely stall a DC motor