CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends

Posted by Leslie Watts
on 2005-06-11 13:54:33 UTC
>The idea I get from your posts is to make a sleeve that has the ID
>that would fit the OD of the balls. chuck up the shaft and with
>balls, slide the cup/sleeve over the ballscrew, with balls inside.
>now, the sleeve OD would be concentric to the minor dia of the
>ballscrew. hold that sleeve in the streadyrest and turn the bearing
>and pulley end of that section.

>Dave

Almost, Dave.

I guess the point is missed that the method would involve NO ballscrew
machining. In many cases the headstock hole would be too small, or the lathe
would be too short to use a steady rest. In the case of rolled screws the
land portion is a rough uneven burr. It cannot be used as a datum in a
steady rest.
(some ground screws can). After affixing the cap/end to the screw it could
be further
machined since it is now a good secondary datum to the ball race, but there
is no need. Complete all machining on the cap first.

So just the cap is machined. The screw never goes on a lathe.

I think a drawing is in order!

Les

Leslie M.Watts
L M Watts Furniture
Tiger Georgia
(706) 212-0242

Main page:
http://www.lmwatts.com
Engineering:
http://www.lmwatts.com/shop.html
Cnc surplus for sale:
http://www.lmwatts.com/forsale.html
Carved signs:
http://www.lmwatts.com/signwp.html










Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links

Discussion Thread

Marcus and Eva 2005-06-09 22:01:50 UTC Re: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Leslie Watts 2005-06-10 05:36:36 UTC RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends turbulatordude 2005-06-10 06:33:05 UTC Re: fitting ballscrew ends Marcus and Eva 2005-06-10 07:50:06 UTC Re: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Leslie Watts 2005-06-10 09:01:34 UTC RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Fred Smith 2005-06-10 09:43:57 UTC Re: fitting ballscrew ends Marcus and Eva 2005-06-10 22:21:13 UTC Re: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Leslie Watts 2005-06-11 07:31:24 UTC RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends turbulatordude 2005-06-11 08:07:26 UTC Re: fitting ballscrew ends Marcus and Eva 2005-06-11 08:23:57 UTC Re: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Leslie Watts 2005-06-11 08:43:36 UTC RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends turbulatordude 2005-06-11 12:12:28 UTC Re: fitting ballscrew ends Jon Elson 2005-06-11 12:24:10 UTC Re: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends Leslie Watts 2005-06-11 13:54:33 UTC RE: [CAD_CAM_EDM_DRO] Re: fitting ballscrew ends mmeyers1111 2005-06-11 17:23:53 UTC Re: fitting ballscrew ends