Re: A "little" off topic- CHEAP end mills!
Posted by
rickchownyk2000
on 2005-07-07 22:10:21 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
must have been all the heat in the warehouse at Rolands!
I WILL GO BUY A FEW AND REPORT BACK FRIDAY!!! IF THEY ARE BAD, I'LL
RUN (SHUDDER!!) EMC ON THE RICK-O-MATIC (or at least try it)
I have bought a lot from them and my best deal a few years back were
m-42 overstock that were UNDER a buck a piece. still usin' em! And
be nice to them thar old guys-we will be there someday...... Rick
> rickchownyk2000 wrote:been
>
> >Ok, I know I am going to get my wrist slapped, but darn, these are
> >cheap! (I am the "cheap and free" guy, you know!) I have used
> >many "bargain" endmills from Wholesale tool and they have always
> >of good quality. http://www.wttool.com/endmills.html Rick-o-maticwith
> >
> >
> Ohhhhhh, NOOooooo! I'll bet these things are in blue plastic cases
> a paper label, with the size rubber stamped in blue ink! I hadbeen buying
> overstock, etc. end mills from a couple of outfits with excellentluck,
> untilflyers.
> the above-described CRAP started turning up in everybody's sales
> The last batch looked like they'd been free-hand sharpened by ablind
> 90-yearend
> old guy, and this is giving a bum rap to the blind and aged! These
> millsvowed
> lasted a couple minutes each before they started to break down. I
> "Never again!" I've had much better luck since then buying only M-42 and
> M-57 Cobalt cutters, which are of much better quality, bothmetallurgically
> and in terms of sharpening, and the M-42 lasts 5 times as long asplain
> HSS in mostly aluminum machining. On sale, these M-42 cutters arehardly
> any more than the HSS junk (although I don't find them for $1.00)shops are
>
> Do you know WHY WT is selling these at $1.00? Because all the
> now wise to these crap cutters, and wouldn't pop $1.50 for them!ok ok ok ok ok! (I actually heard this post in your own voice!!!)
>
> Jon
must have been all the heat in the warehouse at Rolands!
I WILL GO BUY A FEW AND REPORT BACK FRIDAY!!! IF THEY ARE BAD, I'LL
RUN (SHUDDER!!) EMC ON THE RICK-O-MATIC (or at least try it)
I have bought a lot from them and my best deal a few years back were
m-42 overstock that were UNDER a buck a piece. still usin' em! And
be nice to them thar old guys-we will be there someday...... Rick
Discussion Thread
rickchownyk2000
2005-07-07 18:54:41 UTC
A "little" off topic- CHEAP end mills!
turbulatordude
2005-07-07 19:02:36 UTC
Re: A "little" off topic- CHEAP end mills!
rickchownyk2000
2005-07-07 19:17:04 UTC
Re: A "little" off topic- CHEAP end mills!
Jon Elson
2005-07-07 20:45:53 UTC
Re: [CAD_CAM_EDM_DRO] A "little" off topic- CHEAP end mills!
rickchownyk2000
2005-07-07 22:10:21 UTC
Re: A "little" off topic- CHEAP end mills!
Jon Elson
2005-07-07 22:45:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: A "little" off topic- CHEAP end mills!
R Rogers
2005-07-08 05:44:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: A "little" off topic- CHEAP end mills!