Re: Power Supply & Gecko's
Posted by
smith67au
on 2005-08-14 05:29:35 UTC
-
pretty obvious which are the two AC terminals and the two DC.
The +ve of the capacitor is connected to the +ve wire from the bridge
rectifier, and the -ve likewise.
Is there something else I'm missing here ?
measures no AC voltage at all (with no load).
So I guess it really is a cheap & nasty multimeter.
OK.
Tim
> There are a couple of possibilities. Unless your meter is reallyI'm pretty sure the bridge rectifier is wired up correctly, It's
> substandard,
> it sure looks like you have the rectifier miswired, and are getting
> a lot of
pretty obvious which are the two AC terminals and the two DC.
The +ve of the capacitor is connected to the +ve wire from the bridge
rectifier, and the -ve likewise.
Is there something else I'm missing here ?
> AC sent out to the Gecko drives. That would blow the fuse, ofcourse.
> The Gecko drives should be drawing power straight off the maincapacitor.
> If you are putting heavy AC across the capacitor, that couldactually be
> quite dangerous. If there is any sign of it getting hot, stopimmediately.
> When these larger caps explode, the noise can be louder than agunshot,
> and the shrapnel can also be quite dangerous. (It also makes abloody
> mess!)I managed to get an oscilloscope onto the power supply today, it
> Do you read the 150 VAC directly across the capacitors terminals?
measures no AC voltage at all (with no load).
So I guess it really is a cheap & nasty multimeter.
>be
> >I do have some smaller caps around 9000uf and 10000uf if it would
> >better dropping down in size.I ran the machine for an hour or so today (at 42VDC ) and all seemed
> >
> >
> Reducing the capacitor value is not going to solve this problem.
>
> Jon
OK.
Tim
Discussion Thread
smith67au
2005-08-13 05:48:19 UTC
Power Supply & Gecko's
caudlet
2005-08-13 08:30:33 UTC
Re: Power Supply & Gecko's
Peter Reilley
2005-08-13 08:43:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
Andy Wander
2005-08-13 08:45:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
Roy J. Tellason
2005-08-13 09:03:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
wanliker@a...
2005-08-13 09:20:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
turbulatordude
2005-08-13 09:24:39 UTC
Re: Power Supply & Gecko's
turbulatordude
2005-08-13 09:49:03 UTC
Re: Power Supply & Gecko's
Stephen Wille Padnos
2005-08-13 10:06:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
Roy J. Tellason
2005-08-13 10:31:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
smith67au
2005-08-13 15:14:33 UTC
Re: Power Supply & Gecko's
Jon Elson
2005-08-13 18:49:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply & Gecko's
smith67au
2005-08-14 05:29:35 UTC
Re: Power Supply & Gecko's