Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
Posted by
Jon Elson
on 2005-09-06 21:25:11 UTC
cstrudwicke@... wrote:
Acrobat labels the pages differently, so i'm guessing you mean Acrobat's
page 53, which is actually page 49 of the document.
That page seems to be 4 serial data level translators and an FPGA.
A square on a schematic with an FPGA is not going to do you much good,
either, without the configuration information for the FPGA. The interface to
the analog scales is actually on the next page, where it shows the 15-pin D
connectors with the SIN+/SIN- and COS+/COS- signals going into an
op-amp. But, that's all there is on that page, and that is a FAR cry from an
interpolator.
Jon
>Look at page 53.There is no page 53 of the manual, as the pages themselves are labeled.
>
Acrobat labels the pages differently, so i'm guessing you mean Acrobat's
page 53, which is actually page 49 of the document.
That page seems to be 4 serial data level translators and an FPGA.
A square on a schematic with an FPGA is not going to do you much good,
either, without the configuration information for the FPGA. The interface to
the analog scales is actually on the next page, where it shows the 15-pin D
connectors with the SIN+/SIN- and COS+/COS- signals going into an
op-amp. But, that's all there is on that page, and that is a FAR cry from an
interpolator.
Jon
>CS
>
>
>
>>Jon Elson <elson@...> wrote:
>>
>>cstrudwicke@... wrote:
>>
>>
>>
>>>Have a look at the rear of this manual :
>>>
>>>http://www.deltatau.com/fmenu/ACC-51P.pdf
>>>
>>>This is a 4096x interpolator board from Delta Tau.
>>>
>>>
>>>
>>>
>>>
>>No, it is just a signal conditioner that converts the differential
>>sin/cos
>>signals to single-ended, and feeds them to an ADC that is processed
>>by the Delta-Tau DSP processor. So, there is almost nothing actually
>>shown in those schematics.
>>
>>Jon
>>
>>
>>
>>Addresses:
>>FAQ: http://www.ktmarketing.com/faq.html
>>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
>>timg@...
>>Moderator: pentam@... indigo_red@... davemucha@...
>>[Moderators]
>>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>>OFF Topic POSTS: General Machining
>>If you wish to post on unlimited OT subjects goto:
>>aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
>>if you have trouble.
>>http://www.metalworking.com/news_servers.html
>>
>>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>>sister site to the CCED group, as many of the same members are there,
>>for OT subjects, that are not allowed on the CCED list.
>>
>>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
>> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>>bill
>>List Mom
>>List Owner
>>
>>
>>Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>Yahoo! Groups Links
>
>
>
>
>
>
>
>
Discussion Thread
protman16
2005-09-06 10:55:15 UTC
Looking for scale interprolator circut
cstrudwicke@o...
2005-09-06 16:43:31 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
Jon Elson
2005-09-06 18:20:17 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
cstrudwicke@o...
2005-09-06 21:04:21 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
Jon Elson
2005-09-06 21:25:11 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
craig strudwicke
2005-09-07 02:41:34 UTC
RE: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
Jon Elson
2005-09-07 09:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
bazer_20002000
2005-09-07 11:57:55 UTC
Re: Looking for scale interprolator circut
protman16
2005-09-07 13:05:38 UTC
Re: Looking for scale interprolator circut
th.carel
2005-09-08 06:18:34 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
Mariss Freimanis
2005-09-10 17:11:53 UTC
Re: Looking for scale interprolator circut
Mcginnis, Darrell S
2005-09-12 16:28:07 UTC
RE: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut
John Johnson
2005-09-13 05:27:07 UTC
Re: [CAD_CAM_EDM_DRO] Looking for scale interprolator circut