Re: [CAD_CAM_EDM_DRO] Servo Heating
Posted by
R Rogers
on 2006-04-25 10:58:10 UTC
Oops, yeah you are right...power leads, not motor leads. At any rate, the servos run much cooler with them installed.
Ron
Jon Elson <elson@...> wrote:
R Rogers wrote:
leads, you will have an explosion! I'm not kidding! It will also fry the
Gecko drive.
Jon
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
[Non-text portions of this message have been removed]
Ron
Jon Elson <elson@...> wrote:
R Rogers wrote:
>The "gain" on the G320 is probably set too high. If this is a Bridgeport type machine there shouldnt be that much load on the Y servo, other than inertia. The only axis I've noticed this being a problem is Z driving the 1000lb+ knee and peck drilling, and that is after like 4 solid hours of it.NO NO NO! On the POWER leads. If you put the cap on the MOTOR
>
> One of the things that will help with motors running cooler is a 100volt 1000mf cap right at the drive on the motor leads.
>
>
leads, you will have an explosion! I'm not kidding! It will also fry the
Gecko drive.
Jon
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
[Non-text portions of this message have been removed]
Discussion Thread
vrsculptor
2006-04-24 19:13:51 UTC
Servo Heating
Harko Schwartz
2006-04-24 20:58:48 UTC
Re: [CAD_CAM_EDM_DRO] Servo Heating
R Rogers
2006-04-25 06:50:52 UTC
Re: [CAD_CAM_EDM_DRO] Servo Heating
Jon Elson
2006-04-25 10:14:02 UTC
Re: [CAD_CAM_EDM_DRO] Servo Heating
R Rogers
2006-04-25 10:58:10 UTC
Re: [CAD_CAM_EDM_DRO] Servo Heating