Re: [CAD_CAM_EDM_DRO] G-Rex 3,900 IPM video

The IH23014 when wired bipolar parallel is rated by the manufaturer at 4.2A
so just think how much faster it would run if you cranked her up from 3A to
4.2. It's called "git her done in a hurry!" :)

Dan Mauch
MCG stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch


"The average velocity is 51.4"/sec if accel/decel is included. The
velocity 65.535"/sec after accel, before decel. The motor is an MCG
IH230014 run in parallel at 3A/phase, 24VDC supply, PID closed-loop
on the G100 driving a stock-standard G201."


Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch

----- Original Message -----
From: "Mariss Freimanis" <mariss92705@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Sunday, June 04, 2006 2:34 PM
Subject: [CAD_CAM_EDM_DRO] G-Rex 3,900 IPM video


> OK, taped it, converted to DivX, posted it. Please go to:
>
> http://www.geckodrive.com/product.cfm?pid=19
>
> Then pick 3900IPM.avi. Please download and save; view it from your
> hard drive instead of selecting "open". This will save on bandwidth
> and not irritate our webmaster.:-)
>
> Video: 16 seconds, 1.234MB, 720 X 480 format, encoded using DivX 6.0,
> no audio; had to remove it because I swore when I nearly got nicked
> by the axis.
>
> The average velocity is 51.4"/sec if accel/decel is included. The
> velocity 65.535"/sec after accel, before decel. The motor is an MCG
> IH230014 run in parallel at 3A/phase, 24VDC supply, PID closed-loop
> on the G100 driving a stock-standard G201.
>
> I'll leave the video up one week, then I'll take it down. Enjoy.
>
> Mariss
>
>
>
>
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>