Re: [CAD_CAM_EDM_DRO] Re: Thk slides
Posted by
Stephen Wille Padnos
on 2006-08-25 06:30:27 UTC
caudlet wrote:
ballscrews, I basically wrapped them in paper towels soaked in WD-40. I
got a plastic tablecloth from the dollar store, and wrapped the whole
thing in that. After a day "infusing", the cosmoline just wiped off
with a rag. I also had a problem with the ballnuts feeling "scratchy",
and it was entirely due to the cosmoline. Once I ran it over the screw
several dozen times, cleaning and soaking with WD-40, they were smooth
as silk.
- Steve
>--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Bill Davis" <wdavis@...>Another thing that works to clean Cosmoline is WD-40. When I bought my
>wrote:
>
>
>>Brian, I think you're right, I need to stick the bearing in cleaning
>>
>>
>solution and let it soak a while.
>
>
>>thanks
>>bill
>>
>>
>Bill: Run the bearings back and forth while "painting" on Mineral
>Spirits with a brush. While soaking them will help, it won't wash the
>junk out of the bearings. Once they start to free up you can switch
>to WD40 (more as a cleaner than a lubricant). Another more aggressive
>approach that I sometimes have to use on my slides is brake cleaner
>from the auto store. Works wonders on waxy or junked up surfaces but
>will attack some plastics so be careful.
>
>
ballscrews, I basically wrapped them in paper towels soaked in WD-40. I
got a plastic tablecloth from the dollar store, and wrapped the whole
thing in that. After a day "infusing", the cosmoline just wiped off
with a rag. I also had a problem with the ballnuts feeling "scratchy",
and it was entirely due to the cosmoline. Once I ran it over the screw
several dozen times, cleaning and soaking with WD-40, they were smooth
as silk.
- Steve
Discussion Thread
wdavis364
2006-08-24 14:16:50 UTC
Thk slides
David Speck
2006-08-24 14:45:15 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
Bill Davis
2006-08-24 15:33:24 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
BRIAN FOLEY
2006-08-24 15:37:15 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
David Speck
2006-08-24 15:55:04 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
turbulatordude
2006-08-24 16:12:50 UTC
Re: Thk slides
Bill Davis
2006-08-24 17:11:09 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
Bill Davis
2006-08-24 17:12:44 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
BRIAN FOLEY
2006-08-24 19:20:02 UTC
Re: [CAD_CAM_EDM_DRO] Thk slides
Paul Kelly
2006-08-25 03:54:02 UTC
DB25 cutouts
caudlet
2006-08-25 05:20:54 UTC
Re: Thk slides
Stephen Wille Padnos
2006-08-25 06:30:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thk slides
Dennis Schmitz
2006-08-25 07:41:48 UTC
Re: Thk slides
Bill Davis
2006-08-25 07:56:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thk slides