Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Posted by
ptengin@a...
on 2000-07-12 20:43:04 UTC
In a message dated 07/12/2000 4:09:21 AM Hawaiian Standard Time,
mr.c@... writes:
<< Actually,the problem was not in the motor but in the belt
wanting to skip. I was probably going to need a kevlar or steel belt to
eliminate any stretch. Thanks for the input.
You using XL type cog belts or the newer HTD profile belts? HTD is harder
to find in the smaller sizes but they do exist. They are a lot better in
resisting tooth skip.
Peter
THRD, Inc.
mr.c@... writes:
<< Actually,the problem was not in the motor but in the belt
wanting to skip. I was probably going to need a kevlar or steel belt to
eliminate any stretch. Thanks for the input.
>>Carey,
You using XL type cog belts or the newer HTD profile belts? HTD is harder
to find in the smaller sizes but they do exist. They are a lot better in
resisting tooth skip.
Peter
THRD, Inc.
Discussion Thread
Carey L. Culpepper
2000-07-12 07:07:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Ron Ginger
2000-07-12 07:20:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Robert Bachman
2000-07-12 08:42:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Carlos Guillermo
2000-07-12 10:05:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Ian Wright
2000-07-12 13:14:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Bertho Boman
2000-07-12 13:41:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Carey L. Culpepper
2000-07-12 18:59:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
ptengin@a...
2000-07-12 20:43:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
ptengin@a...
2000-07-12 20:48:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
jacob saunders
2000-07-12 20:57:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Ian Wright
2000-07-13 03:54:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Carey L. Culpepper
2000-07-13 15:52:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Jon Elson
2000-07-13 16:26:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project
Chris Paine
2000-07-16 14:54:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Counterbalancing & Rong-Fu RF-45 Project