CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] encoder wiring

Posted by Dan Mauch
on 2006-09-16 13:24:15 UTC
The three power lead if a dc motor are Red usually +, Black 0 volts and
white is usually the motor case ground.
Does your encoder have any markings as to which brand and model?
Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
----- Original Message -----
From: <cnc002@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, September 16, 2006 12:43 PM
Subject: Re: [CAD_CAM_EDM_DRO] encoder wiring


>
> In a message dated 9/16/2006 3:35:38 P.M. Eastern Daylight Time,
> rocketscientistnate@... writes:
>
> I can't seem to get any response from centroid. Is there any kind of
> tests I can do to figure out the wiring of this motor/encoder? All I
> can see is 3 heavy wires (such as for power) on one plug, and nine
> light ones on the other. They had a prewire kit that seems to have a
> 9 pin d-connector on the end. Is this a universal wiring scheme for
> quarature encoders? would that be wired for my rutex driver or only
> centroids drivers?
>
> Thanks
> Nathan
>
>
>
> The larger wires would be for power to the motor I am sure. The pin-out
> for
> the encoder is not always uniform from one manufacturer to the other and
> neither are the configuration of the connectors. Can you E-mail me all
> of the
> information off of the encoder and motor. I may have some sources that
> can
> help with that.
>
> Randy
>
>
>
> Randy Abernathy
> 4626 Old Stilesboro Road NW
> Acworth, GA 30101-4066
> E-mail: cnc002@...
>
> I furnish technical support, repair, and other related services for your
> industrial woodworking machinery. My background as Senior Service
> Engineer for
> the SCMI Group for nearly fifteen years with factory training, combines
> with
> my extensive background in electronics, mechanics, pneumatics, electrical
> and
> CNC machinery to offer you needed support for your machinery. Services
> include but are not limited to the following:
>
>
> [Non-text portions of this message have been removed]
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>
>

Discussion Thread

Meyclan 2005-04-04 13:17:01 UTC encoder wiring Andy Wander 2005-04-04 13:21:15 UTC RE: [CAD_CAM_EDM_DRO] encoder wiring Meyclan 2005-04-05 10:28:49 UTC Re: encoder wiring rocketscientistnate 2006-09-16 12:34:53 UTC encoder wiring cnc002@a... 2006-09-16 12:59:15 UTC Re: [CAD_CAM_EDM_DRO] encoder wiring R Rogers 2006-09-16 13:14:33 UTC Re: [CAD_CAM_EDM_DRO] encoder wiring R Rogers 2006-09-16 13:19:19 UTC Re: [CAD_CAM_EDM_DRO] encoder wiring Dan Mauch 2006-09-16 13:24:15 UTC Re: [CAD_CAM_EDM_DRO] encoder wiring Dan Mauch 2006-09-16 13:42:24 UTC Re: [CAD_CAM_EDM_DRO] encoder wiring