Re: Proxxon Mill CNC Conversion
Posted by
bty776302
on 2006-09-21 18:21:43 UTC
Graham,
Can you recall the type of bearings you used here? I've removed a thrust
washer and it looks like there is just enough space for a needle roller
thrust bearing. Did you have to mod the plastic housings ?
Darren
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <eexgs@...>
wrote:
Can you recall the type of bearings you used here? I've removed a thrust
washer and it looks like there is just enough space for a needle roller
thrust bearing. Did you have to mod the plastic housings ?
Darren
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <eexgs@...>
wrote:
>
>
> http://www.indoor.flyer.co.uk/personal.htm
>
> Covers my conversion, a digitizing probe I made for it and on it and
> a 4th and 5th axis add on I made. Also shows some other things made
> using it such as propeller moulds.
>
> The working area is more like 1.5" by 5" It is a very small mill,
> good if you want to make very small things. If you don't then a
> bigger mill will suit you better.
>
> General comments: Spindle is good, runs to over 20k and is quite
> quiet. Takes tooling upto 1/8" maximum. Construction is pretty
> good, it has gibs and the nuts have VERY little backlash. I
> recently replaced the washers that act as thrust bearings with
> normal 6mm ID bearings and that has reduced backlash to nearly
> nothing. Before if you tightend out the axial play of the screw it
> would produce too much friction.
>
> Graham
>
Discussion Thread
Andrew Dubinsky
2004-12-13 10:53:41 UTC
Proxxon Mill CNC Conversion
V FONG
2004-12-13 11:35:21 UTC
Re: [CAD_CAM_EDM_DRO] Proxxon Mill CNC Conversion
timgoldstein
2004-12-13 13:08:53 UTC
Re: Proxxon Mill CNC Conversion
Graham Stabler
2004-12-13 13:22:03 UTC
Re: Proxxon Mill CNC Conversion
Andrew Dubinsky
2004-12-13 14:21:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proxxon Mill CNC Conversion
Graham Stabler
2004-12-13 15:56:43 UTC
Re: Proxxon Mill CNC Conversion
Ron
2004-12-13 16:39:01 UTC
Re: Proxxon Mill CNC Conversion
R Rogers
2004-12-13 18:27:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proxxon Mill CNC Conversion
Graham Stabler
2004-12-14 02:46:34 UTC
Re: Proxxon Mill CNC Conversion
Steven Ciciora
2004-12-14 06:03:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proxxon Mill CNC Conversion
Andrew Dubinsky
2004-12-14 07:53:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proxxon Mill CNC Conversion
Richard Garnish
2004-12-14 17:22:30 UTC
Re: Proxxon Mill CNC Conversion
bty776302
2006-09-21 18:21:43 UTC
Re: Proxxon Mill CNC Conversion
Graham Stabler
2006-09-22 01:09:48 UTC
Re: Proxxon Mill CNC Conversion