Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Posted by
Jon Elson
on 2006-11-18 20:51:09 UTC
Wayne Weedon wrote:
I'm doing at
one time. The rings are quite easy to make, in many cases FASTER than jaw
grinding.
I have a Phase-II copy of the Buck adjustable chuck. It has a rather
fancy series
of slots and grooves on the replaceable top jaws, and it would take more
than a
few setups the replicate all that. Maybe a plain block of stock with
the right
holes would fit, but I'm not too sure.
Jon
>Jon Elson wrote:I'm not going to grind a set of jaws for one pulley, which may be all
>
>
>>>
>>>
>>>
>>the pulleys will give an absolute 2:1 ratio over the long term.
>>Depending on
>>how accurately the hubs are bored, there may be some small cyclical error
>>every turn. That's why I always buy the pulleys with undersize bores and
>>bore them up to whatever size I need. I turn rings out of aluminum scrap
>>that have an exact ID to match the pulley's OD, then split the rings.
>>The OD
>>of the ring is not important, but I turn it on the same mounting so that the
>>ID and OD are perfectly concentric. I put these around the pulley when
>>mounting in the lathe, so the pulley is held very accurately concentric
>>to bore
>>the ID.
>>
>>
>>
>>
>
>Jon you need to make yourself some softjaws, much easier ;)
>
>
I'm doing at
one time. The rings are quite easy to make, in many cases FASTER than jaw
grinding.
I have a Phase-II copy of the Buck adjustable chuck. It has a rather
fancy series
of slots and grooves on the replaceable top jaws, and it would take more
than a
few setups the replicate all that. Maybe a plain block of stock with
the right
holes would fit, but I'm not too sure.
Jon
Discussion Thread
Frank
2006-11-18 06:57:48 UTC
Timing Belts and Pulleys
Harko Schwartz
2006-11-18 09:02:08 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Leslie Newell
2006-11-18 09:38:43 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Jon Elson
2006-11-18 14:19:55 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Preston Petty
2006-11-18 14:31:32 UTC
Re: Timing Belts and Pulleys
Wayne Weedon
2006-11-18 16:26:24 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Jon Elson
2006-11-18 20:51:09 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Steve Blackmore
2006-11-19 01:27:03 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Wayne Weedon
2006-11-19 02:44:58 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Steve Stallings
2006-11-19 07:03:05 UTC
Re: Timing Belts and Pulleys
Mark Vaughan
2006-11-19 08:28:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Jon Elson
2006-11-19 16:46:54 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Jon Elson
2006-11-19 16:56:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Steve Blackmore
2006-11-19 17:35:50 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Steve Blackmore
2006-11-19 17:46:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Dave Pope
2006-11-19 19:29:34 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Mark Vaughan
2006-11-20 00:12:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Paul Kelly
2006-11-20 08:31:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Jon Elson
2006-11-20 10:01:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Jon Elson
2006-11-20 10:14:21 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belts and Pulleys
Steve Blackmore
2006-11-20 13:21:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belts and Pulleys
Seiman H
2006-11-20 14:11:17 UTC
Looking for 4:1 Gear ratio for Nema34
turbulatordude
2006-11-20 18:21:58 UTC
Re: Timing Belts and Pulleys