Re: Bridgeport Ballscrew Backlash
Posted by
Polaraligned
on 2007-01-24 12:25:09 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Mike Phillips"
<mikep_95133@...> wrote:
was maxed out at 10,000 hours. Who knows how many more
hours are on it.
No spot is worn to the point that the flaking is gone, or the
chrome for that matter. This is why I decided not to rescrape
it.
it. It still is dripping.
Scott
<mikep_95133@...> wrote:
>I have heard of them wearing. This machine's hour indicator
> I'd be shocked if that Boss had worn out ball screws. Did you check
> the backlash in the middle and at both ends of travel?
was maxed out at 10,000 hours. Who knows how many more
hours are on it.
> Are you using aMachine has no handles.
> test indicator to see what the endplay is in each axis when you
> push/pull on the handle?
>Wear is not completely uniform. This I have found to be normal.
> The ways on a Boss are far wider than stock. Is the flaking or chrome
> still uniform in appearance all over each way surface?
No spot is worn to the point that the flaking is gone, or the
chrome for that matter. This is why I decided not to rescrape
it.
>I let the pump run until machine was dripping after I reassembled
> Make sure the ways and ballscrews are extrememly well lubricated
> before you measure endplay or backlash. Dry machines can cause
> intermittent results that make tracking them down a bear.
it. It still is dripping.
Scott
Discussion Thread
Polaraligned
2007-01-24 06:29:37 UTC
Bridgeport Ballscrew Backlash
Polaraligned
2007-01-24 07:16:08 UTC
Re: Bridgeport Ballscrew Backlash
Jon Elson
2007-01-24 09:58:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
HTCLKI@A...
2007-01-24 10:09:10 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport Ballscrew Backlash
Mike Phillips
2007-01-24 11:34:22 UTC
Re: Bridgeport Ballscrew Backlash
Polaraligned
2007-01-24 12:12:02 UTC
Re: Bridgeport Ballscrew Backlash
Polaraligned
2007-01-24 12:25:09 UTC
Re: Bridgeport Ballscrew Backlash
Peter Reilley
2007-01-24 13:13:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
Mark Vaughan
2007-01-24 13:14:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
R Rogers
2007-01-24 13:19:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
Polaraligned
2007-01-24 14:58:02 UTC
Re: Bridgeport Ballscrew Backlash
Polaraligned
2007-01-24 15:30:16 UTC
Bridgeport Ballscrew Backlash- Test data
Jon Elson
2007-01-24 18:50:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
Jon Elson
2007-01-24 19:04:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
Polaraligned
2007-01-25 04:55:15 UTC
Servo Error, - Was backlash.
Dan Mauch
2007-01-25 07:56:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Ballscrew Backlash
Mark Vaughan
2007-01-25 19:31:25 UTC
RE: [CAD_CAM_EDM_DRO] Servo Error, - Was backlash.
Jon Elson
2007-01-26 02:06:44 UTC
Re: [CAD_CAM_EDM_DRO] Servo Error, - Was backlash.