Re: [CAD_CAM_EDM_DRO] Cad/Cam program problem
Posted by
fbcsnh@c...
on 2008-02-18 11:40:14 UTC
Neville and all, I have scratched using AI and am migrating to TurboCad and AutoSketch. I re-drew the block I was experimenting with in TurboCad and was able to import it into DeskNc without a problem. It's all in the learning but I don't need any undo task on the brain!
Thanks, Frank
-------------- Original message --------------
From: NEVILLE WEBSTER <nevillewebster@...>
Hi franklin,
it appears that the files are being exported as splines not single line entities, if you send me the dxf file i will explode it to single line entities so that you can try it.
Might solve the problem
Neville
Franklin York <franklin.york@...> wrote:
I am new to Cad and CNC and have an issue with Desknc that I need some help
with.
I am drawing a basic bearing block that has 4 mounting holes 3/8� from each
edge and
one hole dead center that is �� in diameter. The block is 2� square. I am
using Adobe
Illustrator CS3 to design the block. When I export my file as a DXF and
import it into
Desknc I get an error message �Explode all splines before importing�. I
don�t understand
this as I have used Turbocad, Corel Draw as well as AI and get the same
message. Is
there another Cam program I might test drive to get a better handle on this
or does
someone on the group know what I need to do in AI to fix this?
Stumpman
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Thanks, Frank
-------------- Original message --------------
From: NEVILLE WEBSTER <nevillewebster@...>
Hi franklin,
it appears that the files are being exported as splines not single line entities, if you send me the dxf file i will explode it to single line entities so that you can try it.
Might solve the problem
Neville
Franklin York <franklin.york@...> wrote:
I am new to Cad and CNC and have an issue with Desknc that I need some help
with.
I am drawing a basic bearing block that has 4 mounting holes 3/8� from each
edge and
one hole dead center that is �� in diameter. The block is 2� square. I am
using Adobe
Illustrator CS3 to design the block. When I export my file as a DXF and
import it into
Desknc I get an error message �Explode all splines before importing�. I
don�t understand
this as I have used Turbocad, Corel Draw as well as AI and get the same
message. Is
there another Cam program I might test drive to get a better handle on this
or does
someone on the group know what I need to do in AI to fix this?
Stumpman
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Discussion Thread
Franklin York
2008-02-17 17:23:04 UTC
Cad/Cam program problem
caudlet
2008-02-17 17:37:44 UTC
Re: Cad/Cam program problem
Michael Milligan
2008-02-17 23:49:28 UTC
RE: [CAD_CAM_EDM_DRO] Cad/Cam program problem
NEVILLE WEBSTER
2008-02-18 02:49:51 UTC
Re: [CAD_CAM_EDM_DRO] Cad/Cam program problem
Mic
2008-02-18 05:12:58 UTC
Re: Cad/Cam program problem
Fred Smith
2008-02-18 06:30:03 UTC
Re: Cad/Cam program problem
fbcsnh@c...
2008-02-18 11:39:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cad/Cam program problem
fbcsnh@c...
2008-02-18 11:40:14 UTC
Re: [CAD_CAM_EDM_DRO] Cad/Cam program problem