CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] ball screw conversion

Posted by fortino tan
on 2009-11-26 16:51:49 UTC
hiwin does have ready to install X-Y ballscrew for manual retrofit. Check this link : http://hiwin.com/html/bs/xy.html

thanks

Fortino
To: CAD_CAM_EDM_DRO@yahoogroups.com
From: ng1@...
Date: Thu, 26 Nov 2009 19:09:26 +0000
Subject: [CAD_CAM_EDM_DRO] ball screw conversion




























Does anyone have advice on or experience with adding ball screws to an Acer knee mill?


















_________________________________________________________________
New Windows 7: Simplify what you do everyday. Find the right PC for you.
http://windows.microsoft.com/shop

[Non-text portions of this message have been removed]

Discussion Thread

microset3 2009-11-26 11:09:39 UTC ball screw conversion fortino tan 2009-11-26 16:51:49 UTC RE: [CAD_CAM_EDM_DRO] ball screw conversion microset3 2009-11-26 16:56:04 UTC Re: ball screw conversion fortino tan 2009-12-03 01:14:46 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bryan Mumford 2009-12-03 08:10:52 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bob Campbell 2009-12-03 08:24:05 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bryan Mumford 2009-12-03 08:44:55 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bob Campbell 2009-12-03 08:57:56 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion tjwal 2009-12-03 09:15:54 UTC Re: ball screw conversion Bryan Mumford 2009-12-03 09:30:50 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bryan Mumford 2009-12-03 09:38:02 UTC [CAD_CAM_EDM_DRO] Re: ball screw conversion Bob Campbell 2009-12-03 10:22:14 UTC RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion Will Holding 2009-12-03 10:44:56 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion Leslie Newell 2009-12-03 11:13:22 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion Bryan Mumford 2009-12-03 11:16:06 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion wanliker@a... 2009-12-03 11:25:03 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion Leslie Newell 2009-12-03 11:59:59 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion Will Holding 2009-12-04 09:33:37 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion roboticscnc 2009-12-05 00:41:32 UTC Re: ball screw conversion stcnc2000 2009-12-05 10:02:15 UTC Re: ball screw conversion Jon Elson 2009-12-05 12:10:54 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion Will Holding 2009-12-05 12:21:16 UTC Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion