Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Posted by
Jon Elson
on 2009-12-05 12:10:54 UTC
roboticscnc wrote:
It seamlessly meges both MPG and jog keys. I use the MPG to step
down the Z on my mill, then use the jog jeys to make a clean-up pass
across a surface, with a constant feed rate. The same would work fine
on a lathe as well.
Jon
> I would like to have MPGs for manual control and a button for powerWell, if that is actually true, then it is just another reason to use EMC2.
> feed.
> It seems that you can't have both in Mach 3 without changing the jog
> mode
It seamlessly meges both MPG and jog keys. I use the MPG to step
down the Z on my mill, then use the jog jeys to make a clean-up pass
across a surface, with a constant feed rate. The same would work fine
on a lathe as well.
Jon
Discussion Thread
microset3
2009-11-26 11:09:39 UTC
ball screw conversion
fortino tan
2009-11-26 16:51:49 UTC
RE: [CAD_CAM_EDM_DRO] ball screw conversion
microset3
2009-11-26 16:56:04 UTC
Re: ball screw conversion
fortino tan
2009-12-03 01:14:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bryan Mumford
2009-12-03 08:10:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bob Campbell
2009-12-03 08:24:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bryan Mumford
2009-12-03 08:44:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bob Campbell
2009-12-03 08:57:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
tjwal
2009-12-03 09:15:54 UTC
Re: ball screw conversion
Bryan Mumford
2009-12-03 09:30:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bryan Mumford
2009-12-03 09:38:02 UTC
[CAD_CAM_EDM_DRO] Re: ball screw conversion
Bob Campbell
2009-12-03 10:22:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Will Holding
2009-12-03 10:44:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Leslie Newell
2009-12-03 11:13:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Bryan Mumford
2009-12-03 11:16:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
wanliker@a...
2009-12-03 11:25:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Leslie Newell
2009-12-03 11:59:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Will Holding
2009-12-04 09:33:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
roboticscnc
2009-12-05 00:41:32 UTC
Re: ball screw conversion
stcnc2000
2009-12-05 10:02:15 UTC
Re: ball screw conversion
Jon Elson
2009-12-05 12:10:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion
Will Holding
2009-12-05 12:21:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw conversion