Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Posted by
Roland Jollivet
on 2010-06-16 06:30:37 UTC
I looked at my old Balls monitor in the shed. Yes, the connections match
Keith's pinouts. I have two of them, but I am in south Africa.
I do have the circuit diagram somwhere if you need it. But i'll have to do
some searching, so let me know.
Regards
Roland
Keith's pinouts. I have two of them, but I am in south Africa.
I do have the circuit diagram somwhere if you need it. But i'll have to do
some searching, so let me know.
Regards
Roland
On 16 June 2010 00:37, <kabowers@...> wrote:
>
>
> On Sun, 13 Jun 2010 21:48:32 -0400, you wrote:
>
> >On Sun, 13 Jun 2010 22:17:58 -0000, you wrote:
> >
> >>visit the homepage
> >>http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/
> >>and click on the new pictures on the upper lines.
> >>
> >>there is a photo of the connector.
> >>
> >>Dave
> >>
> >>
> >>
> >>--- In CAD_CAM_EDM_DRO@yahoogroups.com<CAD_CAM_EDM_DRO%40yahoogroups.com>,
> Roland Jollivet <Roland.Jollivet@...> wrote:
> >>>
> >Looks for all the world like an old Ball Bros. monitor like I have down in
> the basement.
> >Twenty-five years ago it even worked.
> >
> >I'll do a little looking around in my ancient history collection tomorrow
> and see if I can
> >find the documentation without getting dinosaur bit 8=). IIRC back in the
> 80's I had
> >the manual, or at least schematics.
> >
> >Keith Bowers WB4LSJ- Thomasville, NC
> >
> >
> >
> >------------------------------------
> >
> I finally found some connector pinout info:
>
> Ball Bros. Monitor Pinouts:
>
> 1 Horizontal Ground
> 2 One end of brightness pot
> 3 Other end of brightness pot
> 4 Wiper/Swinger of brightness pot
> 5 Arc Ground
> 6 Horizontal Drive
> 7 DC Power in 5"=>12V 9"=>15V
> 8 50 ohm video in
> 9 Vertical Drive
> 10 Vertical/Video Ground
>
> Brigntness pot may already be on PC board
> Don't know value required
>
> Keith Bowers WB4LSJ- Thomasville, NC
>
>
>
[Non-text portions of this message have been removed]
Discussion Thread
gamusick
2010-06-10 16:43:19 UTC
Thanks all for the information on the Allen Bradley Monitor
grunt68_69
2010-06-13 11:52:38 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
turbulatordude
2010-06-13 12:17:12 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-13 13:33:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
turbulatordude
2010-06-13 15:18:36 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-13 18:49:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-14 01:27:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Jon Elson
2010-06-14 08:27:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-14 16:11:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-15 15:37:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Jon Elson
2010-06-15 19:32:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-16 06:30:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor