Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Posted by
kabowers@N...
on 2010-06-15 15:37:46 UTC
On Sun, 13 Jun 2010 21:48:32 -0400, you wrote:
Ball Bros. Monitor Pinouts:
1 Horizontal Ground
2 One end of brightness pot
3 Other end of brightness pot
4 Wiper/Swinger of brightness pot
5 Arc Ground
6 Horizontal Drive
7 DC Power in 5"=>12V 9"=>15V
8 50 ohm video in
9 Vertical Drive
10 Vertical/Video Ground
Brigntness pot may already be on PC board
Don't know value required
Keith Bowers WB4LSJ- Thomasville, NC
>On Sun, 13 Jun 2010 22:17:58 -0000, you wrote:I finally found some connector pinout info:
>
>>visit the homepage
>>http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/
>>and click on the new pictures on the upper lines.
>>
>>there is a photo of the connector.
>>
>>Dave
>>
>>
>>
>>--- In CAD_CAM_EDM_DRO@yahoogroups.com, Roland Jollivet <Roland.Jollivet@...> wrote:
>>>
>Looks for all the world like an old Ball Bros. monitor like I have down in the basement.
>Twenty-five years ago it even worked.
>
>I'll do a little looking around in my ancient history collection tomorrow and see if I can
>find the documentation without getting dinosaur bit 8=). IIRC back in the 80's I had
>the manual, or at least schematics.
>
>Keith Bowers WB4LSJ- Thomasville, NC
>
>
>
>------------------------------------
>
Ball Bros. Monitor Pinouts:
1 Horizontal Ground
2 One end of brightness pot
3 Other end of brightness pot
4 Wiper/Swinger of brightness pot
5 Arc Ground
6 Horizontal Drive
7 DC Power in 5"=>12V 9"=>15V
8 50 ohm video in
9 Vertical Drive
10 Vertical/Video Ground
Brigntness pot may already be on PC board
Don't know value required
Keith Bowers WB4LSJ- Thomasville, NC
Discussion Thread
gamusick
2010-06-10 16:43:19 UTC
Thanks all for the information on the Allen Bradley Monitor
grunt68_69
2010-06-13 11:52:38 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
turbulatordude
2010-06-13 12:17:12 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-13 13:33:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
turbulatordude
2010-06-13 15:18:36 UTC
Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-13 18:49:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-14 01:27:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Jon Elson
2010-06-14 08:27:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-14 16:11:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
kabowers@N...
2010-06-15 15:37:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Jon Elson
2010-06-15 19:32:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor
Roland Jollivet
2010-06-16 06:30:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks all for the information on the Allen Bradley Monitor