RE: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Posted by
Tim Goldstein
on 2000-08-13 16:52:09 UTC
For my purposes getting everything calculated to point of including Denver's
altitude is not required. I do think that at this altitude it takes less
helium to fill a balloon to a particular size in comparison to sea level,
but unfortunately it take a larger volume of gas to get an equal amount of
lift so you do use more helium in Denver if you want equal lift.
Tim
[Denver, CO]
altitude is not required. I do think that at this altitude it takes less
helium to fill a balloon to a particular size in comparison to sea level,
but unfortunately it take a larger volume of gas to get an equal amount of
lift so you do use more helium in Denver if you want equal lift.
Tim
[Denver, CO]
> Doug Harrison wrote:
> >
> > >
> > > Now you have brought in another factor, atmospheric pressure
> in Denver.
> > >
> > > John Grant
> >
> > Just a little more than three percent reduction in pressure per
> 1000 foot of
> > altitude
>
> That would be about a 15% effect, worth thinking about.
>
> > However, the cylinder gage reads differential pressure so this
> should not
> > matter.
>
> But wouldn't that take less gas from the cylinder to get the same
> diameter ballon as sea level?
>
> John Grant
Discussion Thread
JanRwl@A...
2000-08-12 22:24:03 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
JanRwl@A...
2000-08-12 22:29:17 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Jon Elson
2000-08-12 22:35:50 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Doug Harrison
2000-08-13 10:20:44 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Tim Goldstein
2000-08-13 10:58:24 UTC
RE: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
John Grant
2000-08-13 12:03:11 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Doug Harrison
2000-08-13 14:10:31 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
ptengin@a...
2000-08-13 14:27:44 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
John Grant
2000-08-13 15:35:04 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Tim Goldstein
2000-08-13 16:52:09 UTC
RE: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
JanRwl@A...
2000-08-13 16:54:58 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Doug Harrison
2000-08-13 18:37:29 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
Ejay Hire
2000-08-14 07:20:45 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?
dave engvall
2000-08-14 21:37:32 UTC
Re: [CAD_CAM_EDM_DRO] OT: Cubic Feet in a Compressed Gas Cylinder?