Re: [CAD_CAM_EDM_DRO] Emc2 beginner help please?

I bought your machine production. She was in complete and good
condition. Udrom thunder I lost my memory and parameters to start the machine. I
lack the software that I have, because it is destroyed.
It is a machine, "Chiron FZ16 - l NC, 1988.
Please do not enable the software to the machine and help to installit.
With respect Milos Nikolic.



________________________________
From: Michael Fagan <woodworker88@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Sat, January 29, 2011 4:03:22 PM
Subject: Re: [CAD_CAM_EDM_DRO] Emc2 beginner help please?

You need to "home" the axis at the far extent of your travel, and then set a
part zero point at the corner or center of your part. Look for the DRO-like
axis position screen and there are some buttons associated with it.

On Sat, Jan 29, 2011 at 04:08, Brian <electromodeler@...> wrote:

>
>
> Hi folks,
>
> Hoping someone can help me here. I have built a router, installed emc2,
> done the setups, and everything seems fine, I can run toolpaths (air
> cutting!) and jog and all that basic stuff. But for the life of me, I can't
> find out how to start a toolpath at a designated point, ie I can get my
> toolpaths to run, but not from where I made my 0,0 in the cam program. It is
> not the program, as I have tried a few. I do not have home or limit
> switches, and have been using the Sherline reference manual, as they are set
> up like that too. I want to know how, once I have homed all the axis, I can
> get the cutter to start either at the bottom corner, or dead center of the
> job.
>
> I have waded through so many Emc pdf's that i'm cross-eyed. I don't have a
> lot of time to devote to this, and it seems every time is like starting all
> over again. I fully intend to write a beginners guide to emc once I have it
> mastered, as there doesn't seem to be anything like that out there.
>
> Many thanks guys,
>
> Brian
>
>
>


[Non-text portions of this message have been removed]



------------------------------------

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]

URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you
have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister
site to the CCED group, as many of the same members are there, for OT subjects,
that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T
POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner

Yahoo! Groups Links






[Non-text portions of this message have been removed]