CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors!

Posted by Tim Goldstein
on 2000-08-30 08:53:10 UTC
Jon,

How do you alter the GUI refresh rate??

Tim
[Denver, CO]

> I believe the standard GUI update is 5 Hz, which is too slow for my
> liking.
> I don't want it to keep jogging for up to .2 seconds AFTER I take my
> finger OFF the jog buttons! So I always up the GUI rate to 10 Hz.
> If the GUI were going much more than 10 hz, the numbers would
> be a blur.
>
> Jon

Discussion Thread

wanliker@a... 2000-08-29 13:53:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-29 16:02:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jeff Barlow 2000-08-29 17:00:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! dave engvall 2000-08-29 18:01:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! dave engvall 2000-08-29 18:04:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jeff Barlow 2000-08-29 18:22:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Art Fenerty 2000-08-29 18:22:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-29 22:38:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-29 22:59:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Ron Ginger 2000-08-30 06:45:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! dave engvall 2000-08-30 07:22:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Tim Goldstein 2000-08-30 08:53:10 UTC RE: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Alan Marconett KM6VV 2000-08-30 10:49:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jeff Barlow 2000-08-30 11:45:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-30 12:50:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-30 13:17:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-30 13:27:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Carlos Guillermo 2000-08-30 21:19:10 UTC RE: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors! Jon Elson 2000-08-31 13:41:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Lost Steps => time for microprocessors!