Re: [CAD_CAM_EDM_DRO] distance from controller to stepper
Posted by
Dennis Bohlke
on 2000-10-17 07:30:11 UTC
I have used cables up to 28 feet long from the driver to the stepper motor.
The wire gauge becomes a factor. There is power lost in the wire
resistance.
The bigger the individual wire size the better, yet it has to be enough to
bend
when it should. You can tell when you are loosing power in the motor cables
because they get warm when the wire gauge is to small.
I think a 50 foot parallel cable from the computer to the driver may be
solution worth considering. Then keep the driver with the table. That is
what
I do, I have computerized router on the patio and the computer in the
kitchen
with a 25 foot parallel cable between them.
Dennis
The wire gauge becomes a factor. There is power lost in the wire
resistance.
The bigger the individual wire size the better, yet it has to be enough to
bend
when it should. You can tell when you are loosing power in the motor cables
because they get warm when the wire gauge is to small.
I think a 50 foot parallel cable from the computer to the driver may be
solution worth considering. Then keep the driver with the table. That is
what
I do, I have computerized router on the patio and the computer in the
kitchen
with a 25 foot parallel cable between them.
Dennis
----- Original Message -----
From: Chris Salter <salterc@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Tuesday, October 17, 2000 7:04 AM
Subject: [CAD_CAM_EDM_DRO] distance from controller to stepper
> Can someone give me advice on what is maximun distance.
>
> I want to be able to roll my plasma cutting table outside the shop
> approx. 25ft.
>
> Can I use around 25ft. of cable from the controller to the steppers...
>
>
> Thanks
>
> Chris
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>
Discussion Thread
Chris Salter
2000-10-17 07:04:33 UTC
distance from controller to stepper
Dennis Bohlke
2000-10-17 07:30:11 UTC
Re: [CAD_CAM_EDM_DRO] distance from controller to stepper
Mariss Freimanis
2000-10-17 10:29:28 UTC
Re: distance from controller to stepper
beer@s...
2000-10-17 15:41:05 UTC
Re: distance from controller to stepper
Anne Ogborn
2000-10-17 17:56:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: distance from controller to stepper
dougrasmussen@c...
2000-10-17 19:56:48 UTC
Re: distance from controller to stepper
Anne Ogborn
2000-10-17 21:59:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: distance from controller to stepper
Darrell
2000-10-17 22:18:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: distance from controller to stepper
Darrell
2000-10-17 22:20:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: distance from controller to stepper
Jon Elson
2000-10-17 23:17:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: distance from controller to stepper