Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Posted by
Smoke
on 2000-12-01 13:28:49 UTC
We had plenty of pipes to run into! Had to wear hard hats any time we went
into the missle area.
Ever get to shoot any?
Smoke
-----Original Message-----
From: Alan Marconett KM6VV <KM6VV@...>
To: CAD_CAM_EDM_DRO@egroups.com <CAD_CAM_EDM_DRO@egroups.com>
Date: Friday, December 01, 2000 1:40 PM
Subject: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
into the missle area.
Ever get to shoot any?
Smoke
-----Original Message-----
From: Alan Marconett KM6VV <KM6VV@...>
To: CAD_CAM_EDM_DRO@egroups.com <CAD_CAM_EDM_DRO@egroups.com>
Date: Friday, December 01, 2000 1:40 PM
Subject: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
>Gordon, Jeff,discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>I was on an FBM Missile Submarine, with Polaris and Poseidon missiles.
>Room? Watch your head (and shins).
>
>Alan KM6VV
>
>
>
>Smoke wrote:
>>
>> I worked with Atlas F missiles..5 guys to a crew and PLENTY of room. 2
>> story launch control center.
>>
>> Yeah, I know much of it is declassified..but not all by any means.
>>
>> At any rate, that was one job I really enjoyed.
>>
>> Smoke
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>
Discussion Thread
Jon Elson
2000-11-29 21:16:15 UTC
Re: missile guidance vs. CNC
Smoke
2000-11-29 21:48:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Jon Elson
2000-11-30 21:40:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Jeff Barlow
2000-11-30 22:08:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Smoke
2000-11-30 22:33:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
dave engvall
2000-11-30 22:52:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Alan Marconett KM6VV
2000-12-01 12:40:17 UTC
Re: missile guidance vs. CNC
Smoke
2000-12-01 13:28:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Alan Marconett KM6VV
2000-12-01 14:13:10 UTC
Re: missile guidance vs. CNC
Jeff Barlow
2000-12-01 14:23:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
Jon Elson
2000-12-01 23:24:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: missile guidance vs. CNC
ballendo@y...
2000-12-03 05:54:38 UTC
Re:Re: missile guidance vs. CNC