CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] High speed spindle chuck

Posted by Smoke
on 2000-12-14 21:09:07 UTC
If your building a spindle, you might want to try looking at the MSC
catalog. They have straight shank double angle collet chucks with 1/2" dia.
shanks that can easily be "fixed" within your spindle. In fact, if you
designe the spindle right you could put a manual drawbar thru the spindle.
this would allow you to have several "quick change" chucks available with
tools already installed. Minimum drill size for these is 1/64".

Smoke


>What are people using for chucks for thier high speed spindles used
>for engraving and PCB routing.
>
>The spindle itself does not seem to hard to make. Bearings rated for
>30K RPM or so are easy to find in catalogs.
>
>Wally K.
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>

Discussion Thread

Wally K 2000-12-14 20:11:55 UTC High speed spindle chuck Tim Goldstein 2000-12-14 20:31:06 UTC RE: [CAD_CAM_EDM_DRO] High speed spindle chuck Smoke 2000-12-14 21:09:07 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck JanRwl@A... 2000-12-14 21:25:05 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Smoke 2000-12-14 21:36:51 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck JanRwl@A... 2000-12-14 21:44:51 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Smoke 2000-12-14 22:07:02 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Jon Elson 2000-12-14 22:08:32 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Greg Nuspel 2000-12-15 03:39:46 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Jon Elson 2000-12-15 12:00:31 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Jon Elson 2000-12-15 12:07:12 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Smoke 2000-12-15 12:09:11 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Jon Elson 2000-12-15 13:51:57 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Wally K 2000-12-15 14:54:35 UTC Re: High speed spindle chuck Smoke 2000-12-15 16:07:10 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Jon Elson 2000-12-15 23:12:53 UTC Re: [CAD_CAM_EDM_DRO] Re: High speed spindle chuck diazden 2000-12-16 22:14:07 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck Smoke 2000-12-16 22:59:34 UTC Re: [CAD_CAM_EDM_DRO] High speed spindle chuck