Re: [CAD_CAM_EDM_DRO] Re: gcode comments
Posted by
Brian Pitt
on 2001-01-27 22:46:33 UTC
On Saturday 27 January 2001 22:03, you wrote:
these are now commonly used on turning centers
G72 stock removal in facing
G71 stock removal in turning
G70 finishing cycle
they let you make several roughing passes leaving some stock
for the finish pass and then run a sooth continuous path finish
cut
the whole range of G7X has so many flavors that trying to enforce
any "Standards" on them would be like herding cats ;-)
Brian
> ballendo@... wrote:sure but by what definition?
> > Example: G20,G21 are COMMONLY used
> > nowadays for inch/mm programming. Used to be G70,G71. For now I think
> > we should be 'backward compatible to 70 and 71, BUT we should also
> > support 20 and 21... There are LOTS of other examples!
>
> It's G20, G21 in the EMC's interpreter. Should G70/71 be added?
these are now commonly used on turning centers
G72 stock removal in facing
G71 stock removal in turning
G70 finishing cycle
they let you make several roughing passes leaving some stock
for the finish pass and then run a sooth continuous path finish
cut
the whole range of G7X has so many flavors that trying to enforce
any "Standards" on them would be like herding cats ;-)
Brian
Discussion Thread
Alan Marconett KM6VV
2001-01-25 10:55:29 UTC
Re: gcode comments
Jon Elson
2001-01-25 15:29:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: gcode comments
ballendo@y...
2001-01-25 18:18:52 UTC
Re: gcode comments
Alan Marconett KM6VV
2001-01-25 19:09:30 UTC
Re: gcode comments
ballendo@y...
2001-01-25 21:20:23 UTC
Re: gcode comments
Ray
2001-01-26 18:35:37 UTC
Re: gcode comments
Alan Marconett KM6VV
2001-01-26 19:11:12 UTC
Re: gcode comments
ballendo@y...
2001-01-27 19:03:41 UTC
Re: gcode comments
Matt Shaver
2001-01-27 22:04:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: gcode comments
Brian Pitt
2001-01-27 22:46:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: gcode comments
Raymond Henry
2001-01-28 20:08:41 UTC
Re: Re: gcode comments
ballendo@y...
2001-01-29 16:02:45 UTC
Re: gcode comments
ballendo@y...
2001-01-29 16:25:38 UTC
re:Re: gcode comments
ballendo@y...
2001-01-29 19:37:12 UTC
re:Re: Re: gcode comments
Brian Pitt
2001-01-30 02:22:54 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: gcode comments
ballendo@y...
2001-01-30 21:14:58 UTC
re:re:Re: gcode comments
Smoke
2001-01-30 21:32:45 UTC
Re: [CAD_CAM_EDM_DRO] re:re:Re: gcode comments
Brian Pitt
2001-01-30 23:48:17 UTC
Re: [CAD_CAM_EDM_DRO] re:re:Re: gcode comments
ballendo@y...
2001-01-31 03:20:13 UTC
re:re:Re: gcode comments
ballendo@y...
2001-01-31 03:50:09 UTC
re:re:Re: gcode comments