RE: [CAD_CAM_EDM_DRO] Panel Layout Software
Posted by
Donald Kelley
on 2001-04-05 11:43:28 UTC
Thanks for the responses that I have gotten... I have looked
under 'nesting' and other similar terms. Although I have found
lots of commercial software(addons, etc), I was looking for
something free(no or low cost) even if it was constrained. ie
2d, no colors, no accounting for kerf etc.
thanks
don
-----Original Message-----
From: Jon Elson [mailto:jmelson@...]
Sent: Thursday, April 05, 2001 2:35 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Panel Layout Software
Donald Kelley wrote:
know as 'nesting' programs. You might have better luck looking
under that term.
Jon
Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
Addresses:
Post message: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager
FAQ: http://www.ktmarketing.com/faq.html
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
under 'nesting' and other similar terms. Although I have found
lots of commercial software(addons, etc), I was looking for
something free(no or low cost) even if it was constrained. ie
2d, no colors, no accounting for kerf etc.
thanks
don
-----Original Message-----
From: Jon Elson [mailto:jmelson@...]
Sent: Thursday, April 05, 2001 2:35 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Panel Layout Software
Donald Kelley wrote:
> Hi,I can't direct you to a particular program, but these programs are
>
> Speaking of Drawings.... nice segue huh :-)
>
> I suddenly have a need for finding efficient layup
> of rectangular flat parts on a sheet of stock. Like
> cutting pieces out of a sheet of plywood or flame (plasma)
> cutting pieces from standard sized plate metal. I am aware that
know as 'nesting' programs. You might have better luck looking
under that term.
Jon
Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
Addresses:
Post message: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager
FAQ: http://www.ktmarketing.com/faq.html
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Donald Kelley
2001-04-05 04:52:01 UTC
Panel Layout Software
John Stevenson
2001-04-05 05:39:49 UTC
Re: Panel Layout Software
Jon Elson
2001-04-05 11:35:05 UTC
Re: [CAD_CAM_EDM_DRO] Panel Layout Software
Donald Kelley
2001-04-05 11:43:28 UTC
RE: [CAD_CAM_EDM_DRO] Panel Layout Software
Peter Chen
2001-04-05 15:03:25 UTC
Panel Layout Software
Smoke
2001-04-05 18:03:49 UTC
Re: [CAD_CAM_EDM_DRO] Panel Layout Software
Donald Kelley
2001-04-06 08:23:33 UTC
RE: [CAD_CAM_EDM_DRO] Panel Layout Software
Peter Chen
2001-04-06 20:59:33 UTC
Panel Layout Software
Roger Brower
2001-04-07 07:21:33 UTC
Panel Layout Software