CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Am I missing something?

Posted by Joe Vicars
on 2001-05-22 07:21:09 UTC
Flashcut it expensive in my opinion.
You should be able to get everything you need from Dan Mauch, then use cncpro (yeagerautomation.com) as the control. Be about half
the price of Flashcut.
What you don't get is a big flashy windows control. If you really like windows try Art's controller, seems several people on this
list have had good luck with it.
Personally, I won't be switching from CNCpro any time soon. It's just that good, and cheap!

info.host@... wrote:

> Thanks for all the replies so far. The mounts do not come with the Sherline
> but are something like $180; the ones from FlashCut, that are hollow so you
> can see through them, are $200 or so. If I was driving the steppers through
> a DOS program then I would not need a signal generator? And I'd be looking
> for an 80v @ 8amp power supply to drive four steppers?
>
> Thanks again,
> John H.
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

info.host@b... 2001-05-21 17:16:16 UTC Am I missing something? Doug Fortune 2001-05-21 17:49:09 UTC Am I missing something? cadcamcenter@y... 2001-05-21 18:11:39 UTC Re: Am I missing something? Alan Marconett KM6VV 2001-05-21 18:30:56 UTC Re: [CAD_CAM_EDM_DRO] Am I missing something? Carol & Jerry Jankura 2001-05-21 18:34:33 UTC RE: [CAD_CAM_EDM_DRO] Am I missing something? ron ginger 2001-05-21 19:04:56 UTC Re: Am I missing something? Carol & Jerry Jankura 2001-05-21 19:11:28 UTC RE: [CAD_CAM_EDM_DRO] Am I missing something? Chris Stratton 2001-05-21 19:28:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Am I missing something? Tim Goldstein 2001-05-21 22:34:07 UTC RE: [CAD_CAM_EDM_DRO] Am I missing something? info.host@b... 2001-05-22 05:52:05 UTC Re: [CAD_CAM_EDM_DRO] Am I missing something? Joe Vicars 2001-05-22 07:21:09 UTC Re: [CAD_CAM_EDM_DRO] Am I missing something? Alan Marconett KM6VV 2001-05-22 10:39:57 UTC Re: [CAD_CAM_EDM_DRO] Am I missing something? Tim Goldstein 2001-05-22 11:18:49 UTC RE: [CAD_CAM_EDM_DRO] Am I missing something? Alan Marconett KM6VV 2001-05-22 11:35:23 UTC Re: [CAD_CAM_EDM_DRO] Am I missing something? ballendo@y... 2001-05-24 15:37:16 UTC Re: Am I missing something?