Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
Posted by
Jon Elson
on 2001-05-24 10:25:31 UTC
dougrasmussen@... wrote:
is certainly no longer in the hobby class! I thought the $3750 was as
shown, with control, although I couldn't figure out how they could do it
at that price. (Prison labor, maybe?)
end, generally servos are used.
screw, anyway.
Jon
> Jon,OK, I didn't get the bit about the $12K WITH control. Yes, for $12K, it
>
> For this mill as configured with the Fagor control it is slow. I
> don't know the price complete with Fagor, but if in 20 quantity less
> control etc it's $3750 ( I think that's what I read here) then it
> must be at least $12K complete in single quantity. For that price I
> would expect much better performance, wouldn't you?
is certainly no longer in the hobby class! I thought the $3750 was as
shown, with control, although I couldn't figure out how they could do it
at that price. (Prison labor, maybe?)
> I thought this machine had grade 5 ball screws, whatever that means.Well, for low cost, machines are still made with steppers. But, at the higher
> So speed limitations of Acme screws are not an issue here. Also, I
> assume it has servos, I can't imagine any machines are still being
> built with factory made controls and running steppers.
end, generally servos are used.
> At any rate the specs have errors and are very incomplete which makesRight, mm/rev is not much use, and 2000mm/rev would be a VERY coarse
> me wonder about the builder.
screw, anyway.
Jon
Discussion Thread
David M. Munro
2001-05-21 05:56:43 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
William Scalione
2001-05-21 11:34:58 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Jerry Kimberlin
2001-05-21 18:01:52 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Doug Harrison
2001-05-22 19:42:59 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Jerry Kimberlin
2001-05-22 20:02:44 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 08:46:47 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
William Scalione
2001-05-23 13:13:21 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 16:14:41 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Mike Gann
2001-05-23 16:35:23 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
William Scalione
2001-05-23 16:50:42 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 16:52:56 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Mike Gann
2001-05-23 16:59:52 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Jerry Kimberlin
2001-05-23 17:29:49 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
dougrasmussen@c...
2001-05-23 17:31:39 UTC
Re: GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 19:21:14 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 19:40:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
Jerry Kimberlin
2001-05-23 20:02:34 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Smoke
2001-05-23 20:36:03 UTC
Re: [CAD_CAM_EDM_DRO] GEM-500PCN bedmill - CNC ready
Jon Elson
2001-05-23 20:44:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
dougrasmussen@c...
2001-05-23 22:52:17 UTC
Re: GEM-500PCN bedmill - CNC ready
Jon Elson
2001-05-24 10:25:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
Smoke
2001-05-24 12:06:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
ballendo@y...
2001-05-24 20:34:48 UTC
Re: GEM-500PCN bedmill - CNC ready
ballendo@y...
2001-05-24 20:40:10 UTC
Re: GEM-500PCN bedmill - CNC ready
ballendo@y...
2001-05-24 21:08:03 UTC
Re: GEM-500PCN bedmill - CNC ready
dougrasmussen@c...
2001-05-24 21:14:17 UTC
Re: GEM-500PCN bedmill - CNC ready
Ward M.
2001-05-25 01:07:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready
Smoke
2001-05-28 10:29:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: GEM-500PCN bedmill - CNC ready