Re: [CAD_CAM_EDM_DRO] Re: Fanuc

Wow, sounds like you are in the right park. i will call them and find out
what they have for doc's on the 2 with crt's but sounds like the right
stuff. I'll look again and see if i can find a number somewhere...later
brian f.

----- Original Message -----
From: "Donald Brock" <don.pat.brock@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, July 16, 2001 3:37 AM
Subject: [CAD_CAM_EDM_DRO] Re: Fanuc


> Brian,
>
> This unit you are describing sounds like a 5T and they are fairly
> common although older. They were manufactured in the late 70's to
> early '80's prior to the introduction of the 6T unit which had a CRT.
> The model tag was usually on the front of the 5 ft. or so tall
> cabinet door under the control panel and above the door to the tape
> reader or just above the control panel. It would say 'SYSTEM 5T' if
> it had not come loose. they were usually silk-screened plastic
> attached with a double sided foam tape. The control panels differ
> somewhat according to the maker of the lathe. A separate pendant is
> usually provided by the maker of the lathe elsewhere on the machine.
> I can scan a picture of a 5T and send it to you if you want so you
> can look at it to see if this is what actually have. I ran one on a
> Mazak for years and still do occasionally.
>
> Some of the G and M codes will vary on this control depending on how
> the manufacturer of the lathe implemented the Fanuc system to their
> lathe.
>
> I have access to a 5T manual by Fanuc and to a 5T manual written
> specific to a Mazak M4 with two turrets using this control. You will
> find the 5T system adapted to a varity of lathes. Mazak and Ikigai
> (spelling?) among them.
>
> Donald Brock
>
>
> --- In CAD_CAM_EDM_DRO@y..., "brian" <ka1bbg1@m...> wrote:
> > Hi, i wish i knew where to find a fanuc model #. it is a tape
> unit,they have
> > 3 lathes and 2 have a crt this one does not but all have tape
> units. I found
> > the problem and it is running, enough so they need to get hydraulic
> power up
> > to do more testing. There is a bunch of numbers on the fanuc
> control itself.
> > I will try to find out what the other 2 are as they have
> documentation for
> > the 2 with crt. thanks brian f.
> > ----- Original Message -----
> > From: "Donald Brock" <don.pat.brock@p...>
> > To: <CAD_CAM_EDM_DRO@y...>
> > Sent: Saturday, July 14, 2001 8:44 PM
> > Subject: [CAD_CAM_EDM_DRO] Re: Fanuc
> >
> >
> > > Fanuc without a crt? Is this a 5T or earlier unit?
> > >
> > > Donald Brock
> > >
> > >
> > > --- In CAD_CAM_EDM_DRO@y..., "brian" <ka1bbg1@m...> wrote:
> > > > Ok, my buddy has a shop with screw machines,54 or more. one of
> the
> > > new machines is a lathe with a fanuc controller without a crt. It
> was
> > > disconnected and reconnected at his shop but it will not do
> anything
> > > so I have been called. can anyone "fanuc" me. give me a few simple
> > > commands etc? cul brian f.
> > > >
> > > >
> > > > [Non-text portions of this message have been removed]
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > >
> > > Post messages: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > Moderator: jmelson@a... timg@k... [Moderator]
> > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Manager
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > >
> > >
> > >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>