Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Posted by
Rich D.
on 2001-07-19 12:41:39 UTC
Drew, et al,
A note of clarification:
The info below is largely for the older GE motor and controller
no longer available from Surplus center.
The new motor and controller is 90VDC permag with a KB electronics
controller. The two types function the same but the parts cannot
be swapped around. The KB is much superior to the GE.
I have both types and they are good stuff.
Rich D.
Drew Rogge wrote:
~ ~~ ~ ~ ~~ ~~____~,~~ ~~~~
\------/ |00|_[]_[]__||0
.|_CMRy_|-|__|________|_|,
__________''oo__oo__---"0=0=0"=o[]o\\______________________________
-==Rich=-=Colorado Midland Railway=-=cmsteam@...=-Atlanta-
----------See my web site: <http://cmsteamer.homestead.com/> ------
A note of clarification:
The info below is largely for the older GE motor and controller
no longer available from Surplus center.
The new motor and controller is 90VDC permag with a KB electronics
controller. The two types function the same but the parts cannot
be swapped around. The KB is much superior to the GE.
I have both types and they are good stuff.
Rich D.
Drew Rogge wrote:
>11&seekm=8252tc%24ikb%241%40izalco.d-and-d.com#p
> Just a note for anyone interested in getting into the treadmill
> motors at Surplus Center.
>
> These motors have been discussed pretty extensively in RCM over
> the years. You can search the archive at google and come up
> with a bunch of info. In particular the URL:
>
> http://groups.google.com/groups?hl=en&safe=off&ic=1&th=1871dbd6bf968e95,
>--
> will get you a discussion on how to reverse the direction of the
> motors.
>
> Also there are various file format flavors of the schematic
> of the motor controller at:
>
> http://www.metalworking.com/dropbox/_1998_retired_files/
>
> Look for treadmot.???. Also the file treadmot.txt talks about
> two mods which have been worked out for the motor. The first mod
> is to remove one of the transistors (pretty sure it's T3) on the
> board which defeats a "feature" of the controller which prevents
> the motor from starting unless the speed control pot has been
> turned down to zero. The second mod is to cut a trace running to
> pin 6 of the control chip and then connecting the pin to ground.
> This change bypasses the "slow start feature" of the controller.
> Both of these features make sense for use in a treadmill but
> may not be applicable when using these motors on a machine tool.
>
> Have fun,
> Drew
>
> --
> Drew Rogge
> drew@...
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
~ ~~ ~ ~ ~~ ~~____~,~~ ~~~~
\------/ |00|_[]_[]__||0
.|_CMRy_|-|__|________|_|,
__________''oo__oo__---"0=0=0"=o[]o\\______________________________
-==Rich=-=Colorado Midland Railway=-=cmsteam@...=-Atlanta-
----------See my web site: <http://cmsteamer.homestead.com/> ------
Discussion Thread
Chris Difani
2001-07-18 18:06:13 UTC
DC Surplus Motors
David M. Munro
2001-07-19 05:25:04 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
deanc500@y...
2001-07-19 08:02:42 UTC
Re: DC Surplus Motors
Rich D.
2001-07-19 09:57:42 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Jon Elson
2001-07-19 11:08:01 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Drew Rogge
2001-07-19 11:29:49 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Alan Marconett KM6VV
2001-07-19 12:35:55 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Rich D.
2001-07-19 12:41:39 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Rich D.
2001-07-19 12:45:08 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Alan Marconett KM6VV
2001-07-19 13:02:38 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Drew Rogge
2001-07-19 13:40:01 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
mdickey@b...
2001-07-19 15:36:23 UTC
Re: DC Surplus Motors
Rich D.
2001-07-19 16:27:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: DC Surplus Motors
Ron Yost
2001-07-19 18:31:12 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
mslov.joy@v...
2001-07-19 18:58:10 UTC
Re: DC Surplus Motors
Carlos Guillermo
2001-07-20 07:47:18 UTC
Re: DC Surplus Motors