Re: DC Surplus Motors
Posted by
Carlos Guillermo
on 2001-07-20 07:47:18 UTC
Does anyone know how long the brushes will last on these motors?
Are the brushes replaceable?
Carlos Guillermo
VERVE Engineering & Design
-----Original Message-----
From: Rich D. [mailto:cmsteam@...]
Sent: Thursday, July 19, 2001 7:22 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: DC Surplus Motors
Milton,
The KB Controller *is* all the electronics with normally optional
heatsink attached. See their web site <www.kbelectronics.com>
and look for the KBWT-112 unit.
The motor is from another manf.
RichD
Are the brushes replaceable?
Carlos Guillermo
VERVE Engineering & Design
-----Original Message-----
From: Rich D. [mailto:cmsteam@...]
Sent: Thursday, July 19, 2001 7:22 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: DC Surplus Motors
Milton,
The KB Controller *is* all the electronics with normally optional
heatsink attached. See their web site <www.kbelectronics.com>
and look for the KBWT-112 unit.
The motor is from another manf.
RichD
> Drew & others:motor
>
> >From what I'm reading here, this sounds like a great spindle
> for a homebrew mill like the "Heavy Iron" project in Nuts &Volts
> mag. This being a DC motor, does it run properly without anyfurther
> electronic parts on AC line power...just the includedcontroller?
> Forgive my dumb questions, please.
>
> Thanks,
> Milton
Discussion Thread
Chris Difani
2001-07-18 18:06:13 UTC
DC Surplus Motors
David M. Munro
2001-07-19 05:25:04 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
deanc500@y...
2001-07-19 08:02:42 UTC
Re: DC Surplus Motors
Rich D.
2001-07-19 09:57:42 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Jon Elson
2001-07-19 11:08:01 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Drew Rogge
2001-07-19 11:29:49 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Alan Marconett KM6VV
2001-07-19 12:35:55 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Rich D.
2001-07-19 12:41:39 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Rich D.
2001-07-19 12:45:08 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Alan Marconett KM6VV
2001-07-19 13:02:38 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
Drew Rogge
2001-07-19 13:40:01 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
mdickey@b...
2001-07-19 15:36:23 UTC
Re: DC Surplus Motors
Rich D.
2001-07-19 16:27:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: DC Surplus Motors
Ron Yost
2001-07-19 18:31:12 UTC
Re: [CAD_CAM_EDM_DRO] DC Surplus Motors
mslov.joy@v...
2001-07-19 18:58:10 UTC
Re: DC Surplus Motors
Carlos Guillermo
2001-07-20 07:47:18 UTC
Re: DC Surplus Motors