Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Posted by
Chris L
on 2001-07-22 07:12:27 UTC
Weyland wrote:
Also, what is the general opinion on the *size* of
Some of the motor sizing issue for plasma will simply come down to the "mass"
of the moving parts. If you have a real heavy gantry, it will take more to
move it fast. Gearing obviously comes into play as well. I have built one
with some little 80oz motors and she'll safely pull the gantry at speeds up
to 400ipm. I was a bit suprised the first time I ran it! It uses Rack and
pinion.
I could take a look at what my final drive ratios ended up to be if you'd
like. Knowing that much can save a lot of time.
Chris
Also, what is the general opinion on the *size* of
> stepper motor/servo needed for moving a plasma cutterWeyland,
> versus a mill or lathe?
> Obviously, a plasma cutter doesn't need anywhere near the
> torque *or* speed.........
Some of the motor sizing issue for plasma will simply come down to the "mass"
of the moving parts. If you have a real heavy gantry, it will take more to
move it fast. Gearing obviously comes into play as well. I have built one
with some little 80oz motors and she'll safely pull the gantry at speeds up
to 400ipm. I was a bit suprised the first time I ran it! It uses Rack and
pinion.
I could take a look at what my final drive ratios ended up to be if you'd
like. Knowing that much can save a lot of time.
Chris
Discussion Thread
Weyland
2001-07-21 18:08:08 UTC
Introduction & request for help
Carol & Jerry Jankura
2001-07-21 21:13:01 UTC
RE: [CAD_CAM_EDM_DRO] Introduction & request for help
alenz@c...
2001-07-21 21:35:50 UTC
Re: Introduction & request for help
vrsculptor@h...
2001-07-21 21:45:42 UTC
Re: Introduction & request for help
Weyland
2001-07-21 22:20:43 UTC
Re: [CAD_CAM_EDM_DRO] Introduction & request for help
Weyland
2001-07-21 22:24:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Weyland
2001-07-21 22:34:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Weyland
2001-07-21 22:42:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Paul
2001-07-22 02:53:16 UTC
Re: [CAD_CAM_EDM_DRO] Introduction & request for help
Carol & Jerry Jankura
2001-07-22 05:18:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Carol & Jerry Jankura
2001-07-22 05:41:28 UTC
RE: [CAD_CAM_EDM_DRO] Introduction & request for help
Chris L
2001-07-22 07:12:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
brian
2001-07-22 09:24:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Introduction & request for help
Tom Eldredge
2001-07-25 13:13:35 UTC
Re: [CAD_CAM_EDM_DRO] Introduction & request for help
ftomazz
2002-05-31 21:23:04 UTC
Re: Introduction & request for help - did you make it ?