Re: [CAD_CAM_EDM_DRO] Re: Simple DRO sensors - Cheap !

The E2 model is much cheaper if you can use that.

----- Original Message -----
From: <dspinnett@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, November 08, 2001 10:26 PM
Subject: [CAD_CAM_EDM_DRO] Re: Simple DRO sensors - Cheap !


> $30???!!!
> I went to the site, and the "A2" was listed at $270!
> Could you please provide a part number? I am really eager to set up
> dros on my machines (and then do CNC), but I am just getting into
> this roll your own stuff...
> Thanks,.
>
> --- In CAD_CAM_EDM_DRO@y..., Doug Fortune <pentam@h...> wrote:
> > Mark Taft wrote:
> > >
> > > Has anyone found any cheap sensors that can be used to make a
> home brew dro
> >
> > http://www.usdigital.com has high-resolution rotary encoders for
> > about $30 and also high resolution linear encoders for about the
> > same price (the linear 'tape' is $2/inch).
> >
> > As was pointed out by Dave WC0H yesterday, USDigital is coming out
> > with 500 LPI linear strips and encoders (giving 1/(4*500) ==
> 1/2000"
> > resolution in quadrature).
> >
> > Dave 'the newbie' Lantz wrote:
> > >um.... sorry, but what does 'DRO' stand for?
> >
> > 'Digital Read-Out'
> >
> > However in this list when they say 'DRO' usually they mean
> > TTL logic quadrature decoder.
> >
> > Thus the Kulaga/Mauch DRO board is more accurately a
> > TTL logic quadrature decoder ISA board (used perhaps
> > to display a Digital Read Out on a computer screen and/or
> > provide encoder feedback to EMC (a gcode interpreter program).
> > I always make the distinction by calling it a quadrature
> > decoder board (not a DRO board), because DRO display might
> > not be the purpose of the installation of the board.
> >
> > Sometimes on this list 'setting up a table for DRO' actually
> > means installing axes position encoders (either rotary
> > encoders on the screws, to deduce where the table might be,
> > or linear encoders alongside each axis to directly measure
> > where the table is).
> >
> > BTW, quadrature refers to a pair of logic square waves,
> > offset by 90 degrees. When there is movement, not only
> > can you tell the amount of movement by counting the transitions,
> > but you can also tell the direction (left or right) by
> > observing the sequence of changes.
> >
> > Doug Fortune
> > http://www.cncKITS.com
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>