Re: [CAD_CAM_EDM_DRO] flat on shaft
Posted by
Jerry Dees
on 2001-12-05 18:18:24 UTC
Peter,
It would be a good idea to file a flat on the shaft. The day I received
my 2000 I was in a hurry to get the motors on and put them on without a
flat, I got the shaft stuck inside the coupler. If you do get one stuck,
make sure you turn the shaft as you try to pull it out of the coupler. Don't
just pull straight out, the coupler will break.
Jerry
_________________________________________________________
Do You Yahoo!?
Get your free @... address at http://mail.yahoo.com
It would be a good idea to file a flat on the shaft. The day I received
my 2000 I was in a hurry to get the motors on and put them on without a
flat, I got the shaft stuck inside the coupler. If you do get one stuck,
make sure you turn the shaft as you try to pull it out of the coupler. Don't
just pull straight out, the coupler will break.
Jerry
> Hi,Snip
>
> Sherline have some very nicely made motor mounts for their machines,
> plus solid coupler. Their item I am sure are machined to very close
> tolerance. Their dual shafted motors with a flat on the shaft.
>
> If one use a stepper with shaft minus a flat on their coupler and
> motor mount, will the set-screw cause a burr to be raised and thus
> difficulties in removing and/or remounting the motors? Anyone had any
> experience in mounting no-flats shafted steppers on Sherline's motor
> mount?
>
> Many thanks
>
> Peter
_________________________________________________________
Do You Yahoo!?
Get your free @... address at http://mail.yahoo.com
Discussion Thread
cadcamcenter
2001-12-05 17:52:42 UTC
flat on shaft
Jerry Dees
2001-12-05 18:18:24 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Alan Marconett KM6VV
2001-12-05 19:02:52 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Marcus & Eva
2001-12-05 21:17:12 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
ccs@m...
2001-12-05 21:18:58 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
wanliker@a...
2001-12-05 21:55:56 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Alan Marconett KM6VV
2001-12-05 21:56:18 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Tim Goldstein
2001-12-05 22:05:53 UTC
RE: [CAD_CAM_EDM_DRO] flat on shaft
Marcus & Eva
2001-12-06 07:46:14 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Alan Marconett KM6VV
2001-12-06 10:24:56 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Tim
2001-12-06 10:38:42 UTC
RE: [CAD_CAM_EDM_DRO] flat on shaft
Smoke
2001-12-06 11:00:04 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Smoke
2001-12-06 11:05:54 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
cadcamcenter
2001-12-06 12:39:40 UTC
Re: flat on shaft
cadcamcenter
2001-12-06 12:54:42 UTC
Re: flat on shaft
Alan Marconett KM6VV
2001-12-06 14:28:31 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft
Smoke
2001-12-06 16:39:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: flat on shaft
wanliker@a...
2001-12-06 21:44:19 UTC
Re: [CAD_CAM_EDM_DRO] flat on shaft