Re: resistor for power supply
Posted by
cadcamcenter
on 2001-12-10 18:59:02 UTC
JanRwl@A... wrote:
Hi Jan,
(15,000uF)without a current-limiting resistance and it worked fine.
Seems in the long term it is not too good for the system.Don't have
enough experience or knowledge to judge if that is a fair assessment
of the situation.
BTW it seems that 15,000 uF is too large for the requirement (3 2Amp
steppers) and one can do with much smaller cap. In fact I have seen a
3-axes driver where the capacitor (physical size, don't know about
uF) was 10% of that 15,000uF cap on mine.
Many thanks to Bob, Jan, etc
Troll Jr.
Hi Jan,
> This is "theoretically" necessary when15,000 - 20,000 uF seem pretty big to many. I have connected my PS
> the CAP is very, very large, and the
> efficiency of the rectifier is 99%
> example, if a C has "68,000 uF" stamped on it,
> it may-well have a practical
> actual capacitance of 100,000 uF. Even more!
(15,000uF)without a current-limiting resistance and it worked fine.
Seems in the long term it is not too good for the system.Don't have
enough experience or knowledge to judge if that is a fair assessment
of the situation.
BTW it seems that 15,000 uF is too large for the requirement (3 2Amp
steppers) and one can do with much smaller cap. In fact I have seen a
3-axes driver where the capacitor (physical size, don't know about
uF) was 10% of that 15,000uF cap on mine.
Many thanks to Bob, Jan, etc
Troll Jr.
Discussion Thread
cadcamcenter
2001-12-10 16:52:42 UTC
resistor for power supply
Bob Campbell
2001-12-10 17:20:39 UTC
Re: [CAD_CAM_EDM_DRO] resistor for power supply
Christopher Coley
2001-12-10 17:30:01 UTC
RE: [CAD_CAM_EDM_DRO] resistor for power supply
JanRwl@A...
2001-12-10 18:27:17 UTC
Re: [CAD_CAM_EDM_DRO] resistor for power supply
JanRwl@A...
2001-12-10 18:27:50 UTC
Re: [CAD_CAM_EDM_DRO] resistor for power supply
cadcamcenter
2001-12-10 18:59:02 UTC
Re: resistor for power supply
chewy8833
2001-12-10 19:01:13 UTC
Re: resistor for power supply
Carol & Jerry Jankura
2001-12-10 19:06:11 UTC
RE: [CAD_CAM_EDM_DRO] resistor for power supply
mariss92705
2001-12-10 19:07:56 UTC
Re: resistor for power supply
cadcamcenter
2001-12-10 19:09:29 UTC
Re: resistor for power supply
Carol & Jerry Jankura
2001-12-10 19:19:33 UTC
RE: [CAD_CAM_EDM_DRO] Re: resistor for power supply
Matt Shaver
2001-12-10 19:27:17 UTC
Re: [CAD_CAM_EDM_DRO] resistor for power supply
JanRwl@A...
2001-12-10 20:47:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: resistor for power supply
JanRwl@A...
2001-12-10 20:50:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: resistor for power supply
Jon Elson
2001-12-10 21:12:30 UTC
Re: [CAD_CAM_EDM_DRO] resistor for power supply